Bedienungsanleitung Hormann Schuifhekaandrijving (Seite 27 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

538730

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

5.4.1 Recording the CLOSE end-of-travel position via

the limit switch

The limit switch (reed contact) must be connected before

learning the end-of-travel positions. The limit switch wires

must be connected at the REED terminal (see Figure 6.1a).

The option relay has the same function as the red LED during

set-up. The limit switch position can be viewed from afar with

a connected lamp (see Figure 4.4).

Learning the CLOSE end-of-travel position:

Open the gate a bit.1.

Press print button 2. T and keep it pressed.

The gate now travels towards CLOSE at slow speed. The

red LED goes out once the limit switch has been

reached.

Immediately release print button 3. T.

The gate is now in the CLOSE end of travel position.

NOTE:

If the gate travels in the opening direction, DIL switch 1 is in

the wrong position and must be reset. Then repeat steps 1

to 3.

If the position of the gate does not correspond to the desired

CLOSE position, a readjustment must be made.

Readjusting the CLOSE end-of-travel position:

Adjust the position of the magnet by moving the magnet 1.

slide.

Press print button 2. T, until the gate reaches the readjusted

end-of-travel position and the red LED goes out.

Repeat this process until the desired end-of-travel 3.

position has been reached.

5.4.2 Recording the OPEN end-of travel position

See f Figure 6.1b

Learning the CLOSE end-of-travel position:

Press print button 1. T and keep it pressed.

The gate opens at slow speed.

Release print button 2. T once the required OPEN end-of-

travel position is reached.

Press print button 3. P to conﬁrm this position.

The green LED ﬂashes rapidly for 2 seconds to indicate

that the OPEN end-of-travel position has been recorded.

5.4.3 Recording the partial opening end-of-travel

position

Learning the partial opening end-of-travel position:

Press print button 1. T and keep it pressed to move the

gate back towards the CLOSE position.

Release print button 2. T once the desired partial opening

end-of-travel position is reached.

Press print button 3. P to conﬁrm this position.

The green LED ﬂashes slowly to indicate that the partial

opening end-of-travel position has been recorded.

Completion of set-up mode5.4.4

After completion of set-up mode, set f DIL switch 2

(function: learning the gate travel) to OFF.

The green LED signals that forces must be learned by

ﬂashing quickly (see Figure 6.1c).

NOTE:

The safety devices are activated.

Reference cycle5.4.5

See f Figure 6.2

After learning the end-of-travel positions, the ﬁrst cycle

thereafter is always a reference cycle. During this reference

cycle the option relay clocks and a connected warning light

ﬂashes.

Reference cycle to CLOSE end-of-travel position:

Press print button f T once.

The operator automatically moves into the CLOSE end-

of-travel position.

5.5 Learning the forces

Once the end-of-travel positions have been learned and the

reference cycle performed, the forces must be learned. For

this, three successive gate cycles must take place, during

which none of the safety devices may be activated. Recording

the forces takes place automatically by press-and-release

operation (maintained function) in both directions, i.e. once an

impulse has been given, the operator causes the gate to

travel to the end-of-travel position. The green LED ﬂashes

throughout. This LED is steadily illuminated once the force

learning cycles have been completed.

Both of the following procedures must be conducted f

three times.

Learning the forces to the OPEN end-of-travel position:

Press print button f T once.

The operator automatically moves into the OPEN end-of-

travel position.

Learning the forces to the CLOSE end-of-travel position:

Press print button f T once.

The operator automatically moves into the CLOSE end-

of-travel position.

Setting the force limit:

WARNING

Danger of injury if force limit is too high

If the force limit has been set too high, the gate will not stop

on time when closing and may trap persons or objects.

Do not set a force limit that is too high. f

NOTE:

Due to special ﬁtting situations, it can, however, happen that

the previously learned forces prove inadequate which can

lead to undesired reversing. Readjust the forces in such

cases.

A potentiometer is available to set the force limits of the 1.

gate when opening and closing; it is identiﬁed with Kraft

F (Force F) on the control print.

The increase in the force limit is a percentage increase in

relation to the learned values; in the process, the setting

of the potentiometer denotes the following force increase

(see Figure 7.1):

Full left 0% force

Centred +15% force

Right ﬁtting +75% force

TR10A059-C RE / 10.2008 27

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hormann Schuifhekaandrijving Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info