Bedienungsanleitung Hunter ACC (Seite 18 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

InsTallInG sTaTIon modules.....................................................

ACC expands in 6-station increments with intelligent output modules, requiring no tools to install and only a screwdriver

for station wiring connections. The base configuration is 12 stations (two 6-station modules installed) with a maximum

station capacity in a metal wall cabinet of 42 stations (7 total output modules x 6 stations each).

ACC can be expanded at any time with either of the following types of modules:

1. ACM600, 6-station output module with surge suppression and diagnostic LEDs

2. AGM600, 6-station output module with heavy-duty surge suppression and diagnostic LEDs

These two types of modules may be mixed within the same installation if desired.

1. To install expansion modules, turn the dial to the

“Run” position.

2. Open the inner facepack door, and locate the module

lock. Slide the module lock to the “Power Off”

position.

3. Flip up the upper deck cover. Slide the modules up,

into the next available position, viewed from left to

right. Do not skip slots by leaving them empty.

4. Install a module by aligning it firmly in the lower

portion of the next available slot and sliding straight

up until it clicks into place. Once module is in place,

slide power bar to the "Power On" position. The

first two lights of the bottom and top row of each

module installed will light up red for 1 second,

indicating proper contact and the new module has

been recognized. The red lights will then turn off, in

sequence, from left to right across the modules that

are installed.

5. The silver contact on the back of the controller

cabinet must engage a mating slot in the back of the

expansion module. Do not “tip” or force the module

into place. Slide straight up, from the bottom of

the slot.

6. While at the Run dial position, press the Information

button. The current station size will be shown, and

should include any new modules you have added.

US PATIENT NO 6,842,667 B2

ET FLOW SEN4 SEN3 SEN2 SEN1

ET FLOW SEN4 SEN3 SEN2 SEN1 COM

P/M1 P/M2

VAC

1 2 3

4 5 6

7 8 9

10 11 12

13 14 15

16 17 18

19 20 21

22 23 24

25 26 27

28 29 30

31 32 33

34 35 36

3837 39

40 41 42

OUTPUT MODULES (ACM600, AGM600)

A. Station Output Screw Terminals – Connect no more

than two solenoids each.

B. Station Status LEDs – Green for station activity, Red

for fault or short

C. Locking lugs – For module lock

D. Gold plated electrical contacts – Lower rear of

module

E. Additional surge components, AGM versions –

Visible through module

Slide ADM99 in

first 3 slots

Upper Deck cover

ADM99 Decoder

Output Module

ACM600

6-station output

module

AGM600

6-station output module with

heavy duty surge protection

Station Modules

Decoder Output Module

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info