Bedienungsanleitung Hunter ACC (Seite 19 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

CONNECTING THE VALVE WIRES

Each station output module has 6 screw terminals for

connection of individual station wires. The terminals will

accept from 22 AWG (0.64 mm) to 12 AWG (2.05 mm) wires.

Each station output is rated for 0.56 A, max or enough to

operate two typical Hunter solenoids simultaneously.

Once the output module is installed in the slot, the station

numbers assigned to the output module appear in the

upper deck label above each slot.

1. The modules may be removed, if necessary, without

disconnecting the field wiring. However, they must

be reinserted into exactly the same slot, or the

station addresses will be switched.

2. Connect the return wires from the valves to one of

the 3 terminals on the Master Module marked COM.

Since many valve solenoid wires will need to connect

to these 3 common terminals,

3. Route valve wires between control valve location and

controller.

4. At valves, attach a common wire to either solenoid

wire of all valves. This is most commonly a white

colored wire. Attach a separate control wire to

the remaining wire of each valve. All wire splice

connections should be done using waterproof

connectors.

5. Open hinged faceplate on the controller to access the

terminal area.

6. Route valve wires through the conduit and attach

conduit to the controller at the large conduit

openings on the right side of the bottom of the

cabinet.

7. Strip ½" (13 mm) of insulation from ends of all wires.

Secure valve common wire to COM (Common)

terminals on the Master Module. Then attach all

individual valve control wires to appropriate station

terminals.

DECODER OUTPUT MODULE (ADM99)

A. Two Wire Path Terminals – Connect no more than

one pair of red and blue wire paths to each output

terminals

B. Status LEDs– Decoder Fault, Module/Line Activity,

Communicating, Line Status

C. Locking Lugs

D. Gold-plated Electrical Contacts

E. Programming Port – Port where decoder wires get

plugged into in order to program the decoder

Slide ADM99 in

first 3 slots

Upper Deck cover

ADM99 Decoder

Output Module

ACM600

6-station output

module

AGM600

6-station output module with

heavy duty surge protection

Station Modules

Decoder Output Module

1. Decoder output modules may NOT be mixed with the

“conventional” ACM/AGM-600 output modules.

2. Decoder output modules are always installed in the

first three slots.

3. Install the ADM99 by aligning it firmly into the first

three station module slots, and sliding straight up

until clicks into place. As soon as the ADM99 is slide

into place, the Module/Line Activity light will light

red for one second, and then the Line Activity light

will illuminate green. Unlike the station modules,

the ADM99 will illuminate the status lights with the

power bar in the "Power Off" position.

CONNECTING DECODER OUTPUT PATH WIRES

Up to 99 stations may be operated over a single pair of

wires (known as a “path”) using decoders. The decoder

output module allows up to 6 two-wire paths to the field

decoders. The maximum number of decoder stations is

still 99, but multiple paths allow the shortest wire runs.

You may use any number of paths to reach all 99 stations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info