Bedienungsanleitung Hunter ACC (Seite 20 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Each path should consist of Hunter Industries Model

IDWIRE1 or IDWIRE2 color-coded decoder wire. This is

a twisted, solid-core wire suitable for direct burial, and is

always color-coded red and blue.

All red/blue connections in the two-wire path must be

made with DBR6 waterproof connectors or equal.

Each path has a red and a blue terminal with its number on

the decoder output module.

1. Route decoder path wires through the conduit into

the wiring compartment. Leave adequate slack in the

wires for thermal contraction.

2. Strip ½" (13 mm) of insulation from the red and blue

ends.

3. Connect the red wire to the red “1” terminal, and the

blue wire from the same pair to the blue “1”. Repeat

for any other paths as needed.

Do not connect the paths in a loop, or back to any other

point in the controller. Leave the red and blue paths

separate at the end of each two-wire run. Simply insert

decoders in the path until complete, and stop at the

last decoder on the path. If this is not possible, simply

cap each of the ends of the two wire path with a DBR6

waterproof connectors or equal.

Do not connect a wire path from one controller to another

controller!

When a decoder output module is installed, the controller

facepack will recognize it and the station size will change

to “99” (regardless of how many stations are in use). This

will also unlock the normally Extended Decoder displays in

the following dial positions. See DECODER OPERATIONS

(ACC99D VERSIONS) on page 56 for more information.

Key ConneCTIons .......................................................................

1. Common Ground Terminals (x 3) – For return wires

(often white) from stations and master valves. Field

wiring may be returned to any of these 3 terminals

2. P/M1 – Pump/Master Valve output 1, and status light

(return Pump/Master valve circuit to any of the 3 Com

common terminals). Output is 0.320 Amps max

3. P/M2 – Pump/Master Valve output 2, and status light

(return Pump/Master valve circuit to any of the 3 Com

common terminals). Output is 0.320 Amps max

4. Hardwire terminal connection cover – Remove

to install optional ACC-HWIM for hardwired

communications.

5. 24VAC – Always-on 24V test terminal, for locating

valves in the field. Can also be used to power low-draw

sensor receivers such as Hunter WRC. Output is 0.420

amps maximum

6. Flow Sensor connections (+ and -) – Connections for

Hunter HFS flow sensor

7. ET connections (+ and -) – Not used. Connections for

Hunter ET Sensor only. If upper ET terminal is colored

red, Master Module requires update for use with ET.

8. If Master Module has a sticker that says “ET Ready,” or

if the version number of the module is 4.0 or later, the

Master Module is ET ready

9. Sensor Connections (1-4) – Connections for up to 4

Clik-family sensors, or other normally closed switch

contacts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info