595368
22
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
22 – English
OPERATING
Transport and storage
The machine is heavy and can cause serious crush
injuries. Take extra care when loading it onto or off a
vehicle or trailer.
Use an approved trailer to transport the machine.
Check and observe local road traffic regulations before
transporting or driving the machine on roads.
To secure the machine on the trailer, two approved tension
belts and four wedge shaped wheel blocks should be used.
Engage the parking brake and tie the tension belts around
the front and rear brackets.
Secure the machine by tensioning the belts towards the
back and the front of the trailer respectively.
Place the wheel blocks in front of and behind the rear
wheels.
Transport with engine off
Hydraulic pressure must be released in order for the ride-on
mower to be moved when the engine is shutoff.
The hydraulic pressure is opened and closed with a bypass
valve.
Bypass valves
If you try to drive the machine without hydraulic pressure, it
will not move. The drive on the axle is disengaged if one valve
is open.
The P 520D and the P 525D has two valves, one valve for the
front axle and one for the rear axle.
Bypass valve rear axle
The hydraulic pressure is released by opening the locking
nut (1) 1/4-1/2 turn anti-clockwise, then the bypass valve
(2) 2 turns.
The hydraulic pressure is switched on by closing the
valve. Close the valve nut (2) fully before tightening the
locking nut (1).
Bypass valve front axle
The hydraulic pressure is released by opening the locking
nut (1) 1/4-1/2 turn anti-clockwise, then the bypass valve
(2) 2 turns.
The hydraulic pressure is switched on by closing the
valve. Close the valve nut (2) fully before tightening the
locking nut (1).
Winter storage
At the end of the season, or if the machine is going to stand
idle for more than 30 days, it should immediately be made
ready for storage.
For transport and storage of fuel, see the section "Fuel
handling".
To prepare the machine for storage follow these instructions:
Carefully clean the machine, especially under the cutting
unit.
Touch-up paint damage to avoid rust.
Inspect the machine for worn or damaged parts and
tighten loose screws and nuts.
Change the engine oil, and take care of the waste oil.
Fill fuel tank.
Grease all grease nipples, joints and axles.
Remove the battery. Clean it, charge it, and store it in a
cool place.
Store the machine in a clean and dry place and cover it
over for extra protection.
Guard
There is a cover to protect your machine during storage or
transport. Contact your dealer for a demonstration
IMPORTANT! The parking brake is not sufficient to lock the
machine during transport. Ensure you secure the machine
firmly to the transporting vehicle.
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Husqvarna P 520D - 2015 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Husqvarna P 520D - 2015

Husqvarna P 520D - 2015 Bedienungsanleitung - Deutsch - 48 seiten

Husqvarna P 520D - 2015 Bedienungsanleitung - Holländisch - 48 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info