Bedienungsanleitung I-onik WS-209 (Seite 5 von 6) (Deutsch, Englisch)

521902

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

8 9

4. Operating the Bell Box

a. Press the

buttons at the same time for 2 seconds to exit change battery mode and to activa-

te the bell box (all blue lights will be OFF and the red light will start blinking slowly). Your bell box

is now activated.

b. The bell box will now sound within 3 seconds when it receives a wireless signal from the i.onik

Alarmsystem Smart Panel.

c. The Bell Box can be tested by triggering the i.onik

Alarmsystem but be prepared to immediately

disarm the system when you have veried the Bell Box is operating correctly in order to avoid dis-

turbing neighbors. When the bell box is triggered, you can only turn off the bell box by disarming

the i.onik

Alarmsystem Smart Panel. To trigger the i.onik

Alarmsystem, you can press the PANIC

button on the remote or on the keypad of the Smart Panel.

d. If the Bell Box fails to alarm, check the following:

- House Security Settings are the same as for the i.onik

Alarmsystem Smart Panel.

- The Bell Box has been exited from the battery change mode.

- The Bell Box is in a location where it can receive a good signal from the i.onik

Alarmsystem

System Smart Panel.

e. When the Bell Box is activated, removing the Bell Box from the wall surface will trigger the Bell Box

siren immediately.

f. When the battery is running low and needs replacement, the LED indication on the bell box will

blink once every second. In this case follow the battery replacement procedure as described in

Section 5.

5. Changing the Batteries

Always use alkaline batteries of the correct type as replacements because any other batteries can

cause problems with the operation of the bell box. Typical life of batteries is two years.

Ensure the correct steps are taken when changing batteries:

a. Switch off the tamper protection as described in section 3.2.

b. Remove the bell box cover and switch off the bell box power.

c. Remove the used batteries and replace them with 4x fresh

alkaline ‘D’ cells. Alternatively, there is AC power work as a power

back up for the bell box.The AC adaptor is not included.

It is an optional part. You may contact the local distributor to

purchase the AC adaptor separately. You may plug the AC adaptor

into the bell box’s DC power jack (g. on the right)

d. Switch on the bell box power and check that the bell box beeps

and ashes.

e. Fix the bell box cover with the securing screw.

f. Press the

buttons at the same time for 2 seconds to exit the

change battery mode and to activate the bell box (all blue lights will be

OFF and the red light will start to blink slowly). Your bell box is now activated.

6. House Security Code Settings

Unless the factory settings of the Wire-free Home Protection System Smart Panel have been altered,

the House Security Code will NOT need to be changed.

However, if the settings on the Smart Panel have been altered, or need to be altered to solve the

problem of the Smart Panel and sensors activating intermittently (or not working at all) or interfe-

rence with other systems, then the House Security Code on all system modules (sensors, bell box

and all devices) will also need to be changed.

House Security Code settings can be altered as follows:

• There are 4 jumpers or dip-switches on each device.

• Remove the jumper compartment cover, then pull out or plug the jumper into the contacts to

change the House Security Code.

• If a jumper is plugged it is ON if it is removed it is OFF. Default code is with all the jumpers plugged.

• To ensure the system works correctly, make sure the jumpers on the Smart Panel and all other

system modules (sensors, bell box and all devices) match exactly.

7. Lost of Key Fob Remote

In case you lost the key fob remote of the Smart Panel, follow step below to delete the remote from

the bell box.

WARNING!

The siren is very loud, be prepared! Wear protective ear plugs and take care.

• You are not able to disable the tamper protection without the key fob remote that you lost.

• Press & hold the LEARN button for 5 seconds to reset the bell box. All blue lights will be ON

indicating the tamper protection disabled. Your bell box is now reset.

• Press the LEARN button once to enroll the new key fob remote.

• Completing the remote’s enrollment by pressing

buttons on the remote of i.onik

Alarmsystem.

The bell box beeps and ashes once enrollment is successeded.

• Press the learn button to complete the enrollment.

• Fix the bell box cover with the securing screw.

• Press the

button at the same time for 2 seconds to exit change battery mode and to activate

the bell box (all lights will be OFF and the red light will start to blink slowly). Your bell box is now

activated.

8. Maintenance

The product may be cleaned with a soft damp cloth and then wiped dry. Do not use abrasive, solvent

based or aerosol cleaners as this may damage and/or discolour the product. Do not allow water to

enter or attempt to clean inside the unit.

9. Batteries

Do not allow the batteries to corrode or leak as this may cause permanent damage to the product.

Take care to insert the batteries with the correct polarity as shown inside the battery compartments.

Do not mix new and old batteries or different types of batteries. Do not use rechargeable batteries.

At the end of their useful life the batteries should be disposed of via a suitable recycling centre. Do

not dispose of with your normal household waste. DO NOT BURN.

10. Alarm System Limitations

Even the most advanced alarm systems cannot guarantee 100 % protection against burglary or

environmental problems. All alarm systems are subject to possible compromise or failure-to-warn

for a variety of reasons.

Please note that you may encounter problems with your system if:

• The Smart Panel is not placed within hearing range of persons sleeping or remote parts of the

premises.

• The sensors are placed behind doors or other obstacles.

• Intruders gain access through unprotected points of entry (where sensors are not located).

• Intruders have the technical means of bypassing, jamming, or disconnecting all or part of the

system.

Note:

Inadequate maintenance is the most common cause of alarm failure; therefore, test your

system at least once per week to be sure the sensors and sirens are working properly.

Although having an alarm system may make you eligible for reduced insurance premiums,

the system is no substitute for insurance.

Cable Guide

Jumpers for

house

security code

43 21

ON DIP

- Smart Panel

- Each sensor

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

*Jumper: ON = Plugged, OFF = Pull Out

Dip-Switches

for house

security code

- Key Fob Remote

Default house code:

1: ON, 2: ON, 3: ON, 4: ON

I-onik WS-209 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info