Bedienungsanleitung Indesit kp 648 vs b x o (Seite 19 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

324082

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

If an electric fan is used for extracting the combustion

products, the ventilation aperture must be increased in

relation to its maximum performance. The electric fan

should have a sufficient capacity to guarantee an hourly

exchange of air equal to 3 ÷ 5 times the volume of the

kitchen. Prolonged, intensive use of the appliance may

require extra ventilation, e.g. an open window or a more

efficient ventilation system by increasing the extraction

power of the electric fan if installed. Liquid petroleum gas

descends towards the floor as it is heavier than air.

Apertures in the outside walls in rooms containing LPG

cylinders should therefore be at floor level, in order to allow

any gas from leaks to be expelled. Do not store LPG

cylinders (even when empty) in basements/rooms below

ground level; it is advisable to keep only the cylinder in

use in the room and connected far from heat sources which

could raise its temperature to above 50°C.

Gas supply connection

• Check that the appliance is set for the type of gas

available and then connect it to the mains gas piping or

the gas cylinder in compliance with current regulations

and standards.

• This appliance is designed and set to work with the gas

indicated on the label situated on the actual hob. If the

gas supply is different from the type for which the

appliance has been set, proceed with replacing the

corresponding nozzles (provided), following the

instructions given in the paragraph “Adaptation to different

types of gas”.

• For trouble-free operation, suitable use of energy and

longer life of the appliance, make sure that the supply

pressure complies with the values indicated in table 1

"burner and nozzle specifications", otherwise install a

special pressure regulator on the supply pipe in

compliance with current standards and regulations.

• Connect in such a way that the appliance is subjected to

no strain whatsoever.

Either a rigid metal pipe with fittings must be used for

connecting to the threaded cylindrical ½"G male flexible

fitting situated in the rear right-side of the appliance (fig.7),

or a flexible steel tube which must not exceed 2000 mm in

length. Connection must be made in compliance with the

regulations in force.

Should it be necessary to rotate the fitting, definitely replace

the gasket (provided with the appliance).

When the installation has been completed, check the pipe

fittings for leaks using a soapy solution (never use a flame).

Check that the connecting pipe cannot come into contact

with moving parts which could damage or crush it.Check

that the natural gas supply is sufficient for the appliance

when all the burners are in use.

Important: A pressure regulator, in compliance with the

standards in force, must be inserted when connecting to a

liquid gas supply (in a cylinder).

Adapting the cooker to a different type of gas

If the appliance is to be converted for use with a type of

gas different from the one for which it was set in the factory

(indicated on the label to be found on the hob), the burner

nozzles should be replaced as follows:

• remove the grids and the burners.

• unscrew the nozzles "A" (fig.8), using a 7 mm socket

spanner and replace them according to the table 1

"burners and nozzles specifications" with ones which are

suitable for the new type of gas.

• re-assemble all the components.

• on completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

Adjusting the low flame

• Put the tap to the low flame position (the burner should

be lit);

• Remove the tap knob and turn the adjusting screw,

situated to the side of the tap stem (fig. 9) until the flame

is small yet steady, using a screwdriver (loosening the

screw increases the height of the flame, tightening it

decreases it).

N.B.: the adjusting screw must be fully screwed in for

liquid gas.

• having obtained the low flame setting required and with

the burner lit, abruptly change the position of the knob

several times from minimum to maximum and vice ver-

sa and check that the flame does not go out.

• Refit the tap knobs.

fig.7

fig.8

fig.9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit kp 648 vs b x o Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info