Bedienungsanleitung Inventor V6MCRI32-18WiFiR (Seite 23 von 148) (Deutsch, Englisch)

771611

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Page 23 

 Page 22 

Installation Of The Throttle. (Some Models)

Indoor

Outdoor

1 Throttle

2 Liquid pipe

3 Gas pipe

Precautions

- For ensuring throttled efciency, please

mount the throttle as horizontally as possible.

- Wrap the supplied anti-shock rubber at

external of the throttle for denoise.

1 Anti-shock rubber

2 Throttle

CAUTION

• Ensure to wrap insulation around the

piping. Direct contact with the bare piping

may result in burns or frostbite.

• Make sure the pipe is properly connected.

Over tightening may damage the bell

mouth and under tightening may lead to

leakage.

NOTE ON MINIMUM BEND RADIUS

Carefully bend the tubing in the middle

according to the diagram below. DO NOT

bend the tubing more than 90° or more than

3 times.

Bend the pipe with thumb

min-radius 10cm (3.9”)

Fig. 6.10

6. After connecting the copper pipes to the

indoor unit, wrap the power cable, signal

cable and the piping together with binding

tape.

NOTE: DO NOT intertwine signal cable with

other wires. While bundling these items

together, do not intertwine or cross the

signal cable with any other wiring.

7. Thread this pipeline through the wall and

connect it to the outdoor unit.

8. Insulate all the piping, including the valves

of the outdoor unit.

9. Open the stop valves of the outdoor unit

to start the ﬂow of the refrigerant between

the indoor and outdoor unit.

CAUTION

Check to make sure there is no refrigerant

leak after completing the installation work.

If there is a refrigerant leak, ventilate the area

immediately and evacuate the system (refer

to the Air Evacuation section of this manual).

 Page 23 

Wiring 7

Safety Precautions

WARNING

• Be sure to disconnect the power supply

before working on the unit.

• All electrical wiring must be done

according to local and national regulations.

• Electrical wiring must be done by a

qualied technician. Improper connections

may cause electrical malfunction, injury

and ﬁre.

• An independent circuit and single outlet

must be used for this unit. DO NOT plug

another appliance or charger into the same

outlet. If the electrical circuit capacity is not

enough or there is a defect in the electrical

work, it can lead to shock, ﬁre, unit and

property damage.

• Connect the power cable to the terminals

and fasten it with a clamp. An insecure

connection may cause ﬁre.

• Make sure that all wiring is done correctly

and the control board cover is properly

installed. Failure to do so can cause

overheating at the connection points, ﬁre,

and electrical shock.

• Ensure that main supply connection is

made through a switch that disconnects

all poles, with contact gap of a least 3mm

(0.118”).

• DO NOT modify the length of the power

cord or use an extension cord.

CAUTION

• Connect the outdoor wires before

connecting the indoor wires.

• Make sure you ground the unit. The

grounding wire should be away from gas

pipes, water pipes, lightning rods,

telephone or other grounding wires.

Improper grounding may cause electrical

shock.

• DO NOT connect the unit with the power

source until all wiring and piping is

completed.

• Make sure that you do not cross your

electrical wiring with your signal wiring, as

this can cause distortion and interference.

Follow these instructions to prevent distortion

when the compressor starts:

• No other equipment should be connected

to the same power circuit.

• The unit’s power information can be found

on the rating sticker on the product.

• The unit must be connected to the main

outlet. Normally, the power supply must

have a low output impedance of 32 ohms.

NOTE: The fuse is made of ceramic.

TAKE NOTE OF FUSE SPECIFICATIONS

The air conditioner s circuit board(PCB) is

designed with a fuse to provide overcurrent

protection. The specications of the fuse are

printed on the circuit board, such as:

Indoor unit: T3.15A/250VAC, T5A/250VAC.

(applicable for unit adopts R32 refrigerant)

Outdoor unit: T20A/250VAC.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor V6MCRI32-18WiFiR Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor V6MCRI32-18WiFiR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info