Bedienungsanleitung Inventor V6MCRI32-18WiFiR (Seite 24 von 148) (Deutsch, Englisch)

771611

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Page 24 

 Page 24 

b. Using wire strippers, strip the rubber jacket

from both ends of signal cable to reveal

about 15cm (5.9”) of the wires inside.

c. Strip the insulation from the ends of the

wires.

Using a wire crimper, crimp u-lugs on the

ends of the wires.

NOTE: While connecting the wires, please

strictly follow the wiring diagram (found inside

the electrical box cover).

2. Remove the electric cover of the outdoor unit.

If there is no cover on the outdoor unit,

disassemble the bolts from the maintenance

board and remove the protection board. (See

Fig. 7.1)

Connect the u-lugs to the terminals

Match the wire colors/labels with the labels

on the terminal block, and rmly screw the

u-lug of each wire to its corresponding

terminal.

Clamp down the cable with designated cable

clamp.

5. Insulate unused wires with electrical tape.

Keep them away from any electrical or metal

parts.

Reinstall the cover of the electric control box.

Outdoor Unit Wiring

Power Specications

WARNING

Before performing any electrical or wiring

work, turn off the main power to the system.

1. Prepare the cable for connection

a. You must ﬁrst choose the right cable size

before preparing it for connection. Be sure

to use H07RN-F cables.

Table 7.1: Minimum Cross-Sectional Area of

Power and Signal Cables North America

Rated Current of

Appliance (A) AWG

≤ 7 18

7 - 13 16

13 - 18 14

18 - 25 12

25 - 30 10

Table 7.2: Other Regions

Rated Current of

Appliance (A) Nominal Cross-Sectional

Area (mm²)

≤ 6 0.75

6 - 10 1

10 - 16 1.5

16 - 25 2.5

25- 32 4

32 - 45 6

Cover

Screw

Fig. 7.1

Fig. 7.2

1 Control box lid

2 Wiring diagram label

3 Power supply terminal block

4 Clamp for wiring

5 Wiring between units

6 Plastic cover

7 Clamp (eld supply)

 Page 25  

Indoor Unit Wiring

Prepare the cable for connection

Using wire strippers, strip the rubber jacket

from both ends of signal cable to reveal

about 15cm (5.9”) of the wires inside.

Strip the insulation from the ends of the

wires.

c. Using wire crimper, crimp the u-lugs to

the ends of the wires.

Open the front panel of the indoor unit. Using

a screwdriver, remove the cover of the electric

control box on your indoor unit.

Thread the power cable and the signal cable

through the wire outlet.

Connect the u-lugs to the terminals.

Match the wire colors/labels with the labels on

the terminal block, and ﬁrmly screw the u-lug

of each wire to its corresponding terminal. Refer

to the Serial Number and Wiring Diagram

located on the cover of the electric control box.

CAUTION

• While connecting the wires, please strictly

follow the wiring diagram.

• The refrigerant circuit can become very hot.

Keep the interconnection cable away from

the copper tube.

5. Clamp down cable with the designated cable

clamp to secure it in place. The cable should

not be loose, and should not pull on the u-lugs.

6. Reinstall the electric box cover and the front

panel of the indoor unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor V6MCRI32-18WiFiR Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor V6MCRI32-18WiFiR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info