Bedienungsanleitung Jablotron JA-80K (Seite 9 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 9 - MKE51801

other intruder detector within 40 minutes, an alarm will be

triggered. If the first triggered detector has a DEL reaction and

it is not confirmed by any other detector, it will not trigger an

alarm after the entrance delay has expired.

is set (armed).

Exit delay beeps 33x

331 = YES 330 = NO YES The last 5 s faster

Exit delay beeps while partially arming 34x

341 = YES 340 = NO NO The last 5 s faster

Entrance delay beeps 35x

351 = YES 350 = NO YES

Setting (arming) confirmation by wired-siren chirp 36x

361 = YES 360 = NO NO

IW terminal only

Siren always sounds during audible alarms 37x

371 = YES 370 = NO YES

NO = siren only

sounds if the system

is completely set

(armed)

Wireless-siren alarms enabled (IW & EW) 38x

381 = YES 380 = NO YES

Auto-bypass user approval via the ∗ key

If a detector is active during setting (arming), the system will

automatically bypass it (them), immediately (390), or after

keying in ∗ (391)

39x

391 = YES 390 = NO NO to confirm auto-

bypass while exiting

Service mode press #

twice

Final-door detectors

If this function is used, then Exit & Entrance delay settings are

multiplied by 30s. A triggered final-door detector extends the

exit delay, de-triggering of the last final-door detector ends the

exit delay.

65x

0=none, 1=detectors 01 to 05,

2=detectors 46 to 50

x = 0 If multiple F. door

detectors are used,

then triggered

state=any of them,

non triggered state=all

of them

Partial setting (arming) or system splitting 66x

0 = unsplit system

1 = partial setting (A, AB, ABC)

2 = split system A, B & common

section C (set if A & B are set)

unsplit

Automatic Summer Time (Daylight Saving Time)

680x

6801 = YES 6800 = NO NO

Changes internal

clock + 1h on Apr.1 &

-1h on Nov.1

Tamper-signal differential indication -

Tamper alarm in response to an increase in the

number of triggered tamper sensors

681x

6811 = ignore permanently

triggered tamper sensors, i.e.

only react to an increase in

the number of triggered

tamper sensors

6810 =

react with a tamper

alarm to all triggered tamper

sensors

X = 0

Suppresses the

indication of

permanently triggered

tamper sensors

Operating the PG outputs using ∗8 and ∗9

682x

6821 = YES 6820 = NO YES

if yes then arrow keys

can also operate PGX

Permanent alarm status display for a set system

683x

6831 = YES 6830 = NO NO

suppresses the 3min.

display timeout

Tamper alarm if unset (disarmed)

684x

6841 = YES 6840 = NO NO

Recording PG output activation to memory

685x

6851 = YES 6850 = NO YES

Engineer reset

668x

6851 = YES 6850 = N0 NO

Annual check requirement display

If enabled then 12 months after exiting Service Mode an

annual technical check request is displayed on the keypad unit

(mobile phone & ARC notification optional)

690x

6901 = YES 6900 = NO NO

Only single alarm indication

If enabled then another intruder alarm can not be triggered

during an intruder alarm currently in progress.

691x

6911 = YES 6910 = NO NO

Setting (arming) by service code 692x

6921 = YES 6920 = NO NO only with the master

code holder’s

approval

Audible panic alarm 693x

6931 = YES 6930 = NO NO

Higher control-panel receiver-sensitivity

Extends the communication range if there is no RF

interference

694x

6940 = normal 6941 = higher

normal

Access by Code plus Card

If enabled and there is a code and card assigned to the same

user, then both of them must be presented for setting (arming)

control (in any order).

695x

6951 = Code+Card

6950 = Code or Card

code or

card

Audible 24h intruder alarm 696x

6961 = YES 6960 = NO

YES

Service mode only with Service + Master code 697x

6971 = YES 6970 = NO

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80K Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info