Bedienungsanleitung Jablotron JA-80K (Seite 13 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 13 - MKE51801

12.17. Exit delay beeps while partially setting

(arming)

The exit delay caused by partial setting, e.g. using the A or B

key, can also be indicated by keypad beeps and internal-siren

beeps. The beeps get faster in the last 5 seconds.

3 4 1 Beeps enabled

3 4 0 Beeps disabled

Factory default setting: Beeps disabled.

12.18. Entrance delay beeps

The entrance delay can be indicated by keypad beeps and

internal-siren beeps:

3 5 1 Beeps enabled

3 5 0 Beeps disabled

Factory default setting: Beeps enabled

12.19. Setting (arming) confirmation by wired-siren

chirp

A hard-wired siren connected to the IW terminal of the control

panel can audibly indicate setting by one beep, unsetting by two

beeps and unsetting after an alarm by three beeps. Four beeps

mean an invalid attempt at setting the system has occurred.

3 6 1 Chirps enabled

3 6 0 Chirps disabled

Note: In JA-80L wireless sirens, this function can be individually enabled

for each siren. (see the siren manual).

Factory default setting: Hard-wired siren chirps disabled

12.20. Sirens always sound during audible alarms

Using this sequence it is possible to disable internal and external

sirens (IW and EW) if any part of the system is unset (partial

setting), i.e. when someone is home.

3 7 1 Sirens always sound during audible alarms

3 7 0 Sirens only sound during audible alarms when all

sections are set, i.e. no one is home

Factory default setting: Sirens always sound during audible

alarms.

12.21. Wireless siren alarm enabled (IW and EW)

This setting is for enabling and disabling wireless sirens in the

system:

3 8 1 wireless sirens enabled

3 8 0 wireless sirens disabled

Note: This setting has no effect on wired output terminals.

Factory default setting: wireless sirens enabled

12.22. Auto-bypass user approval via the ∗ key

The system has a built-in auto-bypass function so that if any

number of detectors are being triggered during setting (arming)

then they will be bypassed and ignored automatically.

If auto-bypass approval by the user is disabled, then during

setting (arming) the system notes which detectors are currently

triggered and automatically bypasses them without consulting

the user.

If however, auto-bypass user approval is enabled, then during

setting (arming), the system notes which detectors are currently

triggered and displays informative text on the keypad and only

bypasses them if the user approves the bypassing by keying in a

∗ within 6 seconds of being notified.

3 9 1 Approval is requested from the user

3 9 0 Bypassing occurs automatically without user approval

Notes regarding setting the system with (a) triggered detector(s):

• Details on currently triggered detectors can be viewed by pressing the

? key (e.g. open doors or windows).

• If a wireless keyfob is used to set the system and auto-bypass user

approval is enabled, the system will set without bypass approval, i.e.

setting by keyfob does not trigger an approval request.

• The automatic bypass of a detector will end after the detector has

been de-triggered (for example if a door is closed)

• If auto-bypass user approval is enabled and Service mode is being

exited while a detector is being triggered, the installer will be notified

about the bypass. The installer can then approve the bypass by

pressing # twice.

• To comply with the EN-50131-1standard 391 should be set.

Factory default setting: Bypassing occurs automatically

without user approval

12.23. Final-door detectors

In this mode, up to 5 detectors can be defined as final-door

detectors and assigned to addresses 01 to 05 or 46 to 50 in

order to make leaving a building much easier, especially via a

garage:

65x

where x: 0 = none,

1 = detectors on addresses 01 to 05,

2 = detectors on addresses 46 to 50

Description of final-door detector mode:

• If a final-door detector is used in the system then the value of

x for exit delay programming is multiplied by 30 s (see 12.1)

thereby extending the delay, and if an entrance delay is

triggered by a final-door detector then the value of x for the

entrance delay is also multiplied by a larger value of 30 s.

• A final-door detector should be programmed to have a natural

reaction.

• Door/window detectors, hard-wired control panel inputs or

hard-wired inputs in the wireless keypad unit can be used as

final-door detectors.

• If a final-door detector is used for a garage door, no instant

detectors should be inside the garage. Next-delay detectors

would however be acceptable.

Setting (arming) the system with a final-door detector

• After entering a request to set the system, an exit delay of

between 30 to 270 seconds will begin and be indicated.

• If a final-door detector is triggered during the exit delay, the

exit delay will be extended by the time in which the detector is

still triggered. So, if for example, the door is left continuously

open, the exit delay will never end.

• If a final-door detector is de-triggered, the system will wait five

more seconds during which beeping gets faster, and if the

door is not opened again during this short period, the exit

delay will terminate and the system will be set immediately.

• The duration of the exit delay therefore depends on the time

the final door stays open. For instance, in winter if the

driveway in front of a garage needs to be cleared of snow

there will be plenty of time to do it, and in summer when

garages can be exited easily and therefore quickly, the exit

delay can be rather shorter. The exit delay only depends on

the length of time the garage door is left open.

• If no final-door detectors are triggered during the exit delay,

the system will provide an exit delay and then set.

• If the final door detector stays continuously triggered, an

endless exit delay will result with the system never being set.

This means all delayed and next-delayed detectors will not be

set (armed).

• If there are multiple final-door detectors in the system, the exit

delay is extended if any of them is triggered and ends after all

final-door detectors have been de-triggered.

Jablotron JA-80K Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info