Bedienungsanleitung Jablotron JA-80K (Seite 15 von 22) (Englisch)

554835

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Installation manual: Oasis security system JA-80K - 15 - MKE51801

Factory default setting: only 3 minutes of display time

12.29. Tamper alarm if unset

According to EU legislation an unset (disarmed) system should

not audibly sound a tamper alarm if tampering occurs. If the

audible indication of tamper alarms is required while the system

is unset (disarmed) then this can be enabled by the following

sequence:

6841 audible tamper alarm even for an unset system

6840 silent tamper alarm for an unset system

Notes:

• Even if tamper alarms are silent, they are still recorded in the control

panel memory and reported to the end user by SMS, and also to the

ARC if used.

• If the sequence 370 has been programmed, then tamper alarms will

be silent if the system is unset or partially set.

Factory default setting: silent tamper alarms for an unset

system

12.30. Engineer reset

This is a special function requested by the DD243 standard. It can

only be used when the alarm system is connected to an alarm-

receiving center. When a confirmed alarm is activated the control

panel is completely blocked – it cannot be operated by any user,

master or service code until an engineering reset is performed by

an ARC code.

6861 Engineer reset enabled

6860 Engineer reset disabled

Factory default setting: Engineer reset disabled

Notes:

• To enable the confirmation of intruder alarms (requires two detectors to be

triggered in different zones within a definite period) – use sequence 3 2 1

• Reporting to ARCs must be locked by a digital code.

• The keypad shows the text “Eng. reset req’d” and the system stays

blocked until the ARC code is used via the communicator (see manual).

• The feature is supported when a JA-80Y version XA61008 or higher, or a

JA-80V version XA64005 or higher is installed.

12.31. Recording PG output activation to memory

The activation of PGX and PGY outputs can be recorded in the

control panel’s memory (for example if the outputs are used for

access control). This can be enabled by the following sequence:

6851 enabled

6850 disabled

Factory default setting: recording enabled

12.32. Annual check notification

This sequence enables the user and installer to be notified of the

necessary time for an annual technical check:

6900 notification disabled

6901 notification enabled

Notes:

• An annual technical inspection notification is displayed as text on the

keypad display and can also be sent as an SMS to the end user

and/or installer and/or as a report code to an ARC, if used.

• Annual technical inspection notification text disappears on entering

Service Mode

• When this notification is enabled, exiting Service Mode will cause a

notification to occur in the next year on the first day of the month in which it

was set. (e.g. if you set the annual check notification on the 15th October

2007, the notification is displayed on the 1st October 2008.)

• When this notification is enabled, exiting Service Mode will cause a

notification to occur every twelve months later (the same day and

month).

• If you wish to receive a notification earlier than a year later, change

the internal clock settings to the day and month you prefer before

exiting Service Mode by entering 4hhmmDDMMYY, and then re-

adjust the clock to the correct time in maintenance mode. By tricking

the system this way, you can be notified on the desired date. (see

12.45, entering and exiting maintenance mode does not change the

notification date).

Example: If the date is 10 January 2007 and you wish to receive a

notification 6 months later on 10 July 2007, while still in Service Mode

change the system clock to 10 July 2007, i.e. the day and month of the

desired notification date. Then exit Service Mode and re-adjust the clock

to the correct time in maintenance mode.

Factory default setting: Annual inspection notification disabled.

12.33. Only single alarm indication

If this function is enabled, then only one intruder alarm may be

indicated at a time. Once an intruder alarm has been triggered

and has still not ended, then no more alarms can be indicated

no matter how many more times triggering occurs. After the

alarm has ended, the system is then ready to indicate the next

single intruder alarm.

This is to limit the number of SMS reports sent if hard-wired

PIR detectors capable of being frequently triggered are installed

in the system and the system is not unset (disarmed) properly

when someone enters the building.

6 9 1 0 multiple simultaneous intruder alarms allowed

6 9 1 1 single intruder alarm allowed only

Note: Apart from this limitation in the number of simultaneous

intruder alarms, the system also checks to see if any detector is

triggering multiple alarms during the period in which the alarm is

set. Any such undesirable detector is then automatically

bypassed every time the system is set, if it has caused at least

four alarms in a row.

Factory default setting: multiple simultaneous intruder alarms

allowed

Note: A panic alarm can always be triggered with no limits

(except when in service and maintenance modes).

12.34. Setting (arming) by service code

Using this sequence, the installer can be authorized to set and

unset the system by means of a valid service code. This feature

should only be enabled with the explicit approval of the master

code holder (system administrator):

6 9 2 0 disabled

6 9 2 1 enabled

Factory default setting: disabled

12.35. Audible panic alarm

If enabled, panic alarms can be indicated by internal and

external warning devices (sirens on IW and EW):

6 9 3 0 silent panic alarm

6 9 3 1 audible panic alarm

Note: If the sequence 370 is used, panic alarms are silent if any section

of the system is unset.

Factory default setting: silent panic alarm

12.36. Higher control-panel receiver-sensitivity

If enabled, this feature can extend the communication range

between the control panel and its wireless devices if there is no

radio frequency interference in the premises.

6 9 4 0 standard control panel sensitivity

6 9 4 1 higher control panel sensitivity

Note: The sensitivity of the control panel receiver should only be

increased if there is no RF interference as the radio range would only be

reduced if interference was present.

Factory default setting: standard control panel sensitivity

Jablotron JA-80K Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info