Bedienungsanleitung JBSystems MCD150 (Seite 5 von 27) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

468055

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

ENGLISH OPERATION MANUAL

JB SYSTEMS

5/49 MCD150

5. CUE/STUTTER button: Has 2 functions, depending on the playback status:

 STUTTER function: Pressing the CUE button during playback provides an

immediate return to the preprogrammed cue point. Playback starts immediately

from the programmed cue point each time the CUE button is pressed causing a

stutter effect in both normal and loop playback mode.

 CUE function: Pressing the CUE button during pause provides an immediate

return to the preprogrammed cue point. Playback starts immediately for as long as

the CUE button is pressed. The CD player jumps back to the cue point as soon as

the CUE button is released. Please read the chapter called “How to use” to learn

how to set a cue point.

6. PLAY/PAUSE button: Every time you press the PLAY/PAUSE button the CD player

changes from play to pause or from pause to play. The button blinks as long as the

player is set to pause.

7. IN/R.CUE button: Allows you to set the cue point without stopping the playback (CUE

ON THE FLY). This button also sets the beginning of a seamless loop.

8. OUT/EXIT/RELOOP button: Used to set the endpoint when looping music. The player

starts the seamless loop until you press this button again to exit. When a loop is

programmed but not active you can also restart the loop (RELOOP function).

9. SEARCH buttons: These buttons are used to search inside a track. The search speed

increases when you press the buttons for a longer time.

10.TRACK SEARCH Buttons: These buttons are used to select the track to be played.

Forward skip & back skip.

11.LCD DISPLAY: Shows all important information needed during playback. Refer to the

next chapter for more information.

12.TIME Button: The TIME button switches between elapsed playing time, remaining time

in a selection and total remaining time of the disc. (standard = remaining /track) The

“total remaining time of the disc” is not available on MP3 CDs.

13.PITCH BEND buttons: The speed rises while the “+ button” is pressed and returns to

the original pitch when the button is released. The speed drops when the “– button” is

pressed and returns to the original pitch when the button is released. These buttons

can be used to synchronize the beats of 2 tracks.

14.SPEED slider: Press the PITCH button (15), so it is lit. The speed can be changed up

to +/-16% by moving the fader. The speed will not change if the PITCH button (15) is

off. You can change the pitch range with the PITCH RANGE button(16)

15.PITCH Button: This button is used to turn the speed function on and off.

16.PITCH RANGE Button: Every time you press this button, you will change the scale of

the speed slider(14). You can select +/-4%, +/-8% and +/-16%.

ENGLISH OPERATION MANUAL

JB SYSTEMS

6/49 MCD150

17.AUDIO output: Output for the audio signals from the CD-player. Use the supplied

cinch/cinch cable to connect this output to a CD/line input of your mixing unit.

18.DIGITAL OUT socket: Use this connector to connect the digital signal (S/PDIF format)

to the input of a digital amplifier or digital recorder (ex. Mini disc)

19.FADER START Socket: If you are using a mixer with fader start function, use the

supplied mono mini jack/jack cable to connect the player with the fader start of the

mixer. Please note that this socket must never be connected with any voltage.

Attention: This remote control is only compatible with certain (Synq

or Pioneer

compatible) mixers.

Mixers with remote starts functioning with a signal switched to ground will not work.

20.POWER ON/OFF switch: Switches the unit on and off.

21.MAINS input: Connect the CD player to the 230V AC mains, using the supplied power

cord.

LCD DISPLAY

1. TRACK: Shows current track number.

2. TIME BAR: Shows either time remaining or elapsed depending on the setting of the

TIME button. Starts flashing at the end of each track to alert the user to take action.

3. MINUTE: Shows “minutes” time information of current track.

4. SECOND: Shows “seconds” time information of current track.

5. FRAME: Shows “frame” time information of current track. (1 frame = 1/75

sec.)

6. SINGLE: Appears when the unit is set to play just one track at a time. When it is not

shown, the CD plays continuously through all tracks. The function is controlled by the

SGL/CTN button (4).

7. ELAPSED, TOTAL REMAIN: Indicates that the time shown on the display is the track

elapsed, remaining or total remaining time.

8. PITCH DISPLAY: Shows the actual percentage of speed change, selected with the

SPEED slider(14).

HOW TO USE …

Most of the common functions are explained in the previous chapter “controls and

functions” In this chapter we talk about the functions that need a little more explanation.

 PLAYING MP3 FILES:

The CD player automatically detects if a CD contains MP3 files. The MCD150 is able to

read several different MP3 formats but due to display limitations it can’t show the ID3-

tags (song title/performer/…). The CD may contain up to 999 MP3- files, spread over

maximum 255 folders. When the MP3-files are sorted in separate folders, the MCD150

will list all files as if no folders exist.

The MP3-files may have the following file extensions: .mp3 ~ .MP3 ~ .mP3 ~ .Mp3

Check the technical specifications to see which MP3-files are allowed.

JBSystems MCD150 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info