Bedienungsanleitung Juki DDL8700B-7 (Seite 32 von 51) (Englisch)

614555

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

– 30 –

No. Item Description Setting range Default

Ref.

page

64 Change-over speed of

condensation stitch or

EBT (end back tack)

Initial speed when starting condensation stitch or EBT

0 to 250

(sti/min)

1 7 0

70 Function of soft-down of

presser foot

Presser foot is slowly lowered.

0 : Presser foot is rapidly lowered.

1 : Presser foot is slowly lowered.

0/1

71 Double reverse feed

stitching function

Effective/ineffective of double reverse feed stitching is changed over.

(Only used when the CP-18 is used.)

0 : Ineffective

1 : Effective

0/1

72 Sewing machine startup

selecting function

Current limit at the startup of sewing machine is specied.

0 : Normal (Current limit is applied during startup.)

1 : Rapid (Current limit is not applied during startup.)

0/1

73 Retry function This function is used when needle cannot pierce materials .

0 : Retry function is not provided.

1 to 10 : Retry function is provided. (Setting of the needle bar returning

force)

0 to 10

* 76 One-shot function One-shot operation up to the material end is specied.

0 : One-shot operation is not performed.

1 : One-shot operation is performed.

0/1

84 Initial motion suction

time of presser foot

lifting solenoid

Suction motion time of presser foot lifting solenoid

50 to 500

(ms)

2 5 0

87 Function of pedal curve

selection

Pedal curve is selected. (Improving pedal inching operation)

Sewing speed

Pedal stroke

0 to 2

90 Initial motion up stop

function

Automatic UP stop function is set immediately after turning ON the

power.

0 : OFF

1 : ON

0/1

91 Function of prohibiting

compensation operation

after turning handwheel

by hand

It is effective in combination with the machine head provided with tension

release function.

0 : Tension release function is ineffective.

1 : Tension release function is effective.

0/1

92 Function of reducing

speed of reverse feed

stitching at the start of

sewing

Function to reduce speed at the time of completion of reverse feed stitch-

ing at the start of sewing.

0 : Speed is not reduced.

1 : Speed is reduced.

0/1

93 Function added to nee-

dle up/down compensat-

ing switch

Operation of needle up/down compensating switch is changed after

turning ON the power or thread trimming.

0 : Normal (Needle up/down compensating stitching only)

1 : One stitch compensating stitching is performed only when aforemen-

tioned changeover is made. (Upper stop / upper stop)

0/1

95 Head selection function Machine head to be used is selected.

(When the machine head is changed, each setting item is changed to the

initial value of the machine head.)

96 Max. sewing speed Max. sewing speed of the sewing machine head can be set. (The MAX

value differs by machine head.)

150 to MAX

(sti/min)

The setting

differs with the

machine head.

* 103 Needle cooler output

OFF delay time

Delay time from the stop of sewing machine to the output OFF is speci-

ed using the needle cooler output function.

100 to 2000

(ms)

5 0 0

120 Main shaft reference

angle compensation

Main shaft reference angle is compensated.

–50 to 50

- 1 3

121 Up position starting

angle compensation

Angle to detect UP position starting is compensated.

–15 to 15

122 DOWN position starting

angle compensation

Angle to detect DOWN position starting is compensated.

–15 to 15

* 150 Correction of the thread

clamp speed at the start

of sewing

Speed correction coefcient for the function of the thread clamp at the

start of sewing is set. 10 to 200

1 0

* 151 Thread clamp ON angle The angle at which the thread clamp is turned ON at the start of sewing

is set.

0 to 359 (°)

2 1 0

* 152 Thread clamp OFF

angle

The angle at which the thread clamp is turned OFF at the start of sewing

is set.

0 to 359 (°)

2 9 0

* 177 Thread clamp AK oper-

ating time

Function for setting the time for turning ON the AK which operates when

the thread clamp is used.

0 to 1000

(ms)

4 2

181 Setting of a target value

for the production sup-

port function

A target value for the sewing counter of the production support function

is set. 0 to 9999

* Do not change the set values with asterisk (*) mark as they are functions for maintenance. If the standard set value set at the time of

delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated. If it is necessary to

change the set value, please purchase the Engineer’s Manual and follow the instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Juki DDL8700B-7 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info