Bedienungsanleitung Kaysun COMPAK KHP (Seite 14 von 23) (Englisch)

771580

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Installation & Owner's Manual

-25 -15 -5 5 15 25 35 45

Time, hour

Ambient temperature(

℃

)

Heat Up Time within Different Temperature

15-45℃

15-55℃

15-65℃

0.00

1.00

2.00

3.00

4.00

5.00

6.00

-25 -15 -5 5 15 25 35 45

COP

Ambient temperature(

℃

)

COP within Different Temperature

15-45℃

15-55℃

15-65℃

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

-25 -15 -5 5 15 25 35 45

Capacity, W

Ambient temperature(

℃

)

Capacity within Different Temperature

15-45℃

15-55℃

15-65℃

● About TCO and ATCO

The power of E-heater will be automatically shut-off or turn on

by TCO and ATCO.

If the water temperature is higher than 78°C, the ATCO will

automatically shut off the power of compressor and E-heater,

and reconnect it if the temperature falls down below 68°C.

If the water temperature is higher than 85°C, the TCO will

automatically shut off the power of compressor and E-heater.

After that it needs to be reset manually by pressing the red

button on the TCO.

● Restart After a Long Term Stop

When the unit is restarted after a long term stop(trail running

included), it is normal that outlet water is unclean. Keep the tap

on and the water will be clean soon.

Fig.4-4

Fig.4-5

Fig.4-6

NOTE

While the ambient temperature below than -7°C, heat pump

efciency will decrease dramatically, the unit will automatically

shift to E-heater running.

4.2.3 Basic function

1) Weekly disinfect function

Under disinfection unit immediately start to heat water up to 70°C

to kill the potential legionella bacteria inside water of tank,

icon will light on the display screen during disinfection. Unit will

quit disinfection if water temperature is higher than 70°C and

extinguish icon.

2) Vacation function

After pressing button, unit will automatically heat water to

15°C for the purpose of energy saving during vacation days.

3) How is the unit running

If unit is OFF->press

ON/OF FON/OFF

->unit will be waken->press to

set target water temperature(38-65°C)->press ->unit will

automatically select heat source and start to heat water to target

temperature.

4.2.4 Query function

For the convenience of maintenance and debug, query function is

available by press 2 buttons together: + , then

system running parameters will be shown one by one with following

sequence by each pushing of or button.

Table.4-3

No. Hour

low bit

Min.

high bit

Min. Low

bit

Temp./

Dasys Explenation

1Temp. T5U

2Temp. T5L

3Temp. T3

4Temp. T4

5Temp. TP

6Temp. TH

7Current Compressor

8Last error code

9Previous 1st error or

protection code

10 Previous 2nd t error

or protection code

11 Software number

Emptying

Drainpipe shut-off valve

After emptying, please replace the nut of

drainpipe.

Tank

Temperature sensor(T5U)

Electric heater

Water inlet

Water outlet

Temperature sensor(T5L)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun COMPAK KHP Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info