Bedienungsanleitung Kaysun COMPAK KHP (Seite 18 von 23) (Englisch)

771580

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Installation & Owner's Manual

No Icon Description



In vacation period, the setting target water

temperature is 15°C as default and will show the

remanent vacation days. On the last day of vacation,

unit will automatically start disinfect function, and

automatically reset the target temperature to the last

one before vacation.

If unit has already been in vacation or OFF, press

will lead to show invalid icon on the

display.

5.3 Combination button

No Icon Description

Clear

error

code

Press the two buttons at the same

time to clear all stored error &

protect codes, and the buzzer will

buzz one time.

Query +

Press the two buttons at the same

time for 1sec to go into querying.

querying user can check unit

setting & running parameters

by pressing circularly.

Press button for 1s or no

button operation for 30s, then quit

querying.

5.4 Auto-restart

If electricity power failed, unit can memorize all setting parameters,

unit will be back to the previous setting when power recover.

5.5 Button Auto Lock

When there is no operation of button for 1 minute, button will be

locked except Unlock button , Press for 3s, unlock

buttons.

5.6 Screen Auto Lock

If there is no operation of button for 30s, screen will be

locked(extinguished) except for error code and alarm icon.

Press any button will unlock the screen(lighten).

6. TROUBLE SHOOTING

6.1 Non-error tips

Q: Why compressor can't start immediately after setting?

A: Unit will wait for 3 minutes to balance the pressure of system

before starting compressor again, it's a self protection logic of

unit.

Q: Why sometimes the temperature shown on the display panel

decreased while unit is running?

A: When the upper tank temperature is much higher than the

bottom part, upper part hot water will be mixed by the bottom

cold water which is continually ow from inlet tap water so that

will decrease the upper part temperature.

Q: Why sometimes the temperature shown on the display

decreased but unit still keep closed?

A: To avoid unit ON/OFF frequently, unit will activate heat source

only when bottom tank temperature is lower than setting

temperature or max. temperature for at least 5 ºC.

Q: Why sometimes the temperature shown on the display will

decreased dramatically?

A: Because tank is pressure-bearable type, if there is massive hot

demand, hot water will quickly tapped out from upper part of tank

as well as cold water will quickly tapped into bottom part of bank

if the cold water surface emerge the upper temperature sensor,

temperature shown on the display will decreased dramatically.

Q: Why sometimes the temperature shown on the display is decreased

a lot, but there is still a mount of hot water can be tapped?

A: Because the upper water sensor is located on the upper 1/4

tank, when display temperature starts falling down quickly, it

means there is at least 1/4 tank of hot water available.

Q: Why sometimes unit shows "LA" on display ?

A: The heat pump available running ambient range is -7-43°C, if

ambient temperature is out of range, system will show above-

mentioned signal to let user notice it.

Q: Why something there is nothing shown on the display?

A: To maintain display screen lifespan within along term, when

there is no button operation for 30 sec, it will extinguwish the

display except the LED indicator.

Q: Why sometimes the buttons are unavailable?

A: If there is no operation on panel for 1 min, unit will lock the

panel, shows " ", to unlock the panel, please press the

"ENTER" button for 3 seconds.

Q: Why sometimes there is some water owed from drainage pipe

of PTR valve?

A: Because the tank is pressure-bearable one, when water is

heated inside the tank, water will expand, so the pressure inside

of tank will increase, if pressure goes up more than 1.0MPa,

PTR valve will activate to relief the pressure and hot water drop

will be discharged correspondingly. If water drop is continually

discharged from PTR valve drainage pipe, it is abnormal, please

contact qualied stuff to repair.

6.2 Something about self-protection of unit

1) When the self-protection happens, the system will be stopped

and start self-check, and restart when the protection resolved.

2) When the self-protection happens, the buzzer will buzz in every

other minute, the will ash and error code will be shown at

water temperature indicator. Press button for 1sec to

stop buzz, but the and error code does not disappear until

protection resolved.

3) In the following circumstance, self-protection may happen:

Air inlet or outlet is blocked;

The evaporator is covered with too much dust;

Incorrect power supply(exceeding the range of 220-240V).

6.3 When error happened

1) If some normal errors happen, unit will automatically shift to

E-heater for emergent SHW supply, please contact qualied

staff to repair.

2) If some sever errors happen, unit will not start, please contact

qualied staff to repair.

3) If some errors happen, the buzzer will buzz 3 times every other

minute and the will ash fast. Press for 1 sec to stop

the buzzer but the alarm icon will keep glittering.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kaysun COMPAK KHP Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info