686377
14
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
14
A3 MIG Welder© Kemppi Oy 2018 1826
INTEGRATION GUIDE
5.1.8 WireRetract
This signal function feeds the welding wire backwards.
The wire is fed at the speed of 1.0 m/min for 3 seconds
and then stepped to 5.0 m/min.
0 = Wire retract o
1 = Wire retract on
This signal has no eect during welding or simulated
welding.
5.1.9 GasBlow
This signal function opens the shielding gas valve. The gas
valve can be controlled during welding, but not during
simulated welding.
0 = Gas valve closed
1 = Gas valve open
5.1.10 TouchSensorToolSel
This signal function sets the selection of the touch sensing
tool between the welding wire and the gas nozzle.
0 = Welding wire as touch sensing tool
1 = Gas nozzle as touch sensing tool
5.1.11 TouchSensorOn
This signal function sets the touch sensor power source
and the touch detection device to be on. The touch voltage
depends on the conguration. For more information, see
A3 MIG Welder Operating manual.
0 = Touch sensor o
1 = Touch sensor on
This signal has no eect during welding or simulated
welding.
5.1.12 OnlineControl
This signal function enables robot-controlled values for
welding wire feed speed, voltage, and ne tuning. When
the robot is in online mode and uses the WireFeedSpeed,
Voltage, and FineTuning control functions, the corre-
sponding values in the active memory channel are over-
ridden. When the robot is in oine mode, it gives full con-
trol to the welding system and the values from the active
memory channel are used.
0 = Robot in oine mode. The wire feed speed,
voltage, and ne-tuning values are obtained from
the active memory channel.
1 = Robot in online mode and controlling the
wire feed speed, voltage, and ne tuning.
5.1.13 Watchdog
This signal function resets a watchdog timer in the robot
interface unit on each transition. The signal takes eect
when the watchdog function is turned on from the DIP
switches. If the watchdog functionality is on and the robot
can’t maintain transitioning of this signal, the welding
system goes into an error state. This prevents welding
accidents if the robot loses control over the welding
system.
5.1.14 ErrorReset
This signal function resets the ErrorNumber value and the
Error signal to zero on the rising edge of the signal when
there are no active errors in the system. If there are any
active errors, the signal has no eect. The error is active
when the error situation is not yet resolved.
0 = Normal operation
1 = Error reset (on rising edge)
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kemppi A3 MIG Welder wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info