Bedienungsanleitung Kenwood TH-F7E (Seite 17 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

OPERATING THROUGH REPEATERS

Repeaters, which are often installed and maintained

by radio clubs, are usually located on mountain tops

or other elevated locations. Generally they operate at

higher ERP (Effective Radiated Power) than a typical

station. This combination of elevation and high ERP

allows communications over much greater distances

than communications without using repeaters.

Most repeaters use a receive and transmit frequency

pair with a standard or non-standard offset (odd-split).

In addition, some repeaters must receive a tone from

the transceiver to allow it to access. For details,

consult your local repeater reference.

OFFSET PROGRAMMING FLOW

If you store the above data in a memory channel, you

need not reprogram every time. See “MEMORY

CHANNELS” {page 15}.

PROGRAMMING OFFSET

First select an amateur radio repeater downlink

frequency on the A-band or B-band as described in

“SELECTING A FREQUENCY” {page 7}.

■ Selecting Offset Direction

Select whether the transmit frequency will be

higher (+) or lower (–) than the receive frequency.

Press [F], [REV] to select the offset direction.

• “+” or “–” appears, indicating which offset

direction is selected.

• To program –7.6 MHz offset on the TH-F7E

(430 MHz only), repeatedly press [F], [REV]

until “ ” appears.

If the offset transmit frequency falls outside the

allowable range, transmitting is inhibited. In this

case, adjust the receive frequency so that the

transmit frequency is within the band limits.

Note: While using an odd-split memory channel or transmitting,

you cannot change the offset direction.

■ Selecting Offset Frequency

To access a repeater which requires an odd-split

frequency pair, change the offset frequency from

the default which is used by most repeaters. The

default offset frequency on the 2 m band is

600 kHz (all models); the default on the 70 cm

band is 5.0 MHz (TH-F6A) or 1.6 MHz

(TH-F7E); the default on the 1.25 m band is

1.6 MHz (TH-F6A).

1 Press [BAND] to select an amateur radio band

you want to change the offset frequency.

2 Press [MNU].

3 Turn the Tuning control or press [ ]/ [ ] to

select Menu No. 6 (OFFSET).

4 Press [ ] or [MNU].

5 Turn the Tuning control or press [ ]/ [ ] to

select the appropriate offset frequency.

• The selectable range is from 0.00 MHz to

59.95 MHz in steps of 50 kHz.

6 Press [ ] or [MNU] to store the setting.

Otherwise, press [PTT] to cancel.

TH-F7E only: If you have selected “ ” for the offset direction,

you cannot change the default (–7.6 MHz) offset frequency.

Note: After changing the offset frequency, the new offset

frequency will also be used by Automatic Repeater Offset.

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

Select a band.

Select a receive frequency.

Select an offset direction.

Select an offset frequency.

(only when programming odd-split

repeater frequencies)

Activate the Tone function.

(If necessary)

Select a tone frequency.

(If necessary)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info