Bedienungsanleitung Kenwood TH-F7E (Seite 18 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

5 OPERATING THROUGH REPEATERS

■ Activating Tone Function

Press [TONE] to switch the Tone function ON (or

OFF).

•“” appears when the Tone function is ON.

Note: You cannot use the Tone and CTCSS/ DCS functions at

the same time. Switching the Tone function ON after activating

the CTCSS/ DCS deactivates the CTCSS/ DCS function.

TH-F7E only: When you access repeaters that require 1750 Hz

tones, you need not activate the Tone function. Press [CALL]

without pressing the PTT switch to transmit a 1750 Hz tone

(default setting).

■ Selecting a Tone Frequency

1 While the Tone function is ON, press [F],

[TONE].

2 Turn the Tuning control or press [ ]/ [ ] to

select the desired tone frequency.

3 Press [ ] or [MNU] to complete the setting.

Otherwise, press [PTT] to cancel.

Available Tone Frequencies

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

100.76214.79323.141435.602

203.96310.001422.641537.012

309.17415.301524.151631.812

404.47512.701627.651737.522

500.77619.011722.261831.922

607.97718.411829.761936.332

705.28818.811928.371048.142

804.58910.321039.971143.052

905.88023.721132.681241.452

015.19128.131238.291

118.49225.631335.302

Note: 42 different tones are available for the transceiver. These

42 tones includes 37 EIA standard tones and 5 non-standard

tones.

TH-F7E only:

◆

To transmit a 1750 Hz tone, simply press [CALL] without

pressing the PTT switch (default setting). Release [CALL] to

quit transmitting. You can also make the transceiver remain

in the transmit mode for 2 seconds after releasing [CALL]; a

1750 Hz tone is not continuously transmitted. Access Menu

No. 24 (1750 HOLD) and select “ON”.

◆

If you desire to assign [CALL] for recalling the Call channel

in place of transmitting the 1750 Hz tone, access Menu

No. 23 (CALL KEY) and select “CALL”.

AUTOMATIC REPEATER OFFSET

This function automatically selects an offset direction,

according to the frequency that you select on the

2 m and 1.25 m (TH-F6A only) bands. The

transceiver is programmed for offset direction as

shown below. To obtain an up-to-date band plan for

repeater offset direction, contact your national

Amateur Radio association.

TH-F6A (U.S.A. and Canada)

This complies with the standard ARRL band plan.

–

––

144.0 145.5 146.4 147.0 147.6

145.1 146.0 146.6 147.4 148.0 MHz

S: Simplex

–

222.0

225.0 MHz223.920

TH-F7E (Europe/ Others)

S: Simplex

–

144.0

146.0 MHz145.8145.6

Note: Automatic Repeater Offset does not function when Reverse is

ON. However, pressing [REV] after Automatic Repeater Offset has

selected an offset (split) status, exchanges the receive and transmit

frequencies.

1 Press [MNU].

2 Turn the Tuning control or press [ ]/ [ ] to select

Menu No. 5 (AUTO OFFSET).

3 Press [ ] or [MNU].

4 Turn the Tuning control or press [ ]/ [ ] switch

the function ON or OFF.

5 Press [ ] or [MNU] to store the setting.

Otherwise, press [PTT] to cancel.

Note: If you select the frequency within the amateur radio band on

the B-band, the Automatic Repeater Offset function is also activated

in any modes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info