Bedienungsanleitung Kenwood TH-F7E (Seite 19 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

5 OPERATING THROUGH REPEATERS

REVERSE FUNCTION

The reverse function exchanges a separate receive

and transmit frequency. So, while using a repeater,

you can manually check the strength of a signal that

you receive directly from the other station. If the

station’s signal is strong, both stations should move

to a simplex frequency and free up the repeater.

To swap the transmit and receive frequencies:

Press [REV] to switch the Reverse function ON (or

OFF).

• “R” appears when the function is ON.

Note: You can turn the Reverse function ON when you are operating

in Simplex mode. However, it does not change the TX/ RX

frequency.

AUTOMATIC SIMPLEX CHECK (ASC)

While using a repeater, the ASC function periodically

checks the strength of a signal that you are receiving

directly from the other station. If the station’s signal is

strong enough to allow direct contact without a

repeater, “ ” indicator on the display starts blinking.

Press [REV] (1 s) to switch the function ON.

•“” appears when the function is ON.

• While direct contact is possible, “ ” blinks.

• To quit the function, press [REV].

Note:

◆

Pressing the PTT switch causes “ ” icon to quit blinking.

◆

ASC can be activated while operating in Simplex mode.

However, it does not change the TX/ RX frequencies.

◆

ASC does not function while scanning.

◆

Activating ASC while using Reverse switches Reverse OFF.

◆

If you recall a memory channel or the Call channel that contains

a Reverse ON status, ASC is switched OFF.

◆

ASC causes received audio to be momentarily intermitted every

3 seconds.

◆

ASC does not function when the band is not selected for

operation.

TONE FREQ. ID SCAN

This function scans through all tone frequencies to

identify the incoming tone frequency on a received

signal. You may use the function to find which tone

frequency is required by accessing your local

repeater.

1 While the Tone function is ON, press [F],

[TONE] (1 s) to start the Tone Freq. ID scan.

• When the transceiver receives the signal, the

scan starts.

• To reverse the scan direction, turn the Tuning

control or press [ ]/ [ ].

• To quit the function, press [PTT] or [ ].

• When the tone frequency is identified, a beep

sounds and the identified frequency appears.

2 Press [ ] to program the identified frequency in

place of the current tone frequency.

• Press [ ] if you do not want to program the

identified frequency.

• Press [ ]/ [ ] while the identified frequency is

blinking, to resume scanning.

Note: Some repeaters do not re-transmit the access tone in the

downlink signal. In this case, check the other station’s uplink signal

to detect the repeater access tone.

144.725 MHz

145.325 MHz

144.725 MHz

TX: 144.725 MHz TX: 144.725 MHz TX: 144.725 MHz TX: 145.325 MHz

RX: 145.325 MHz RX: 145.325 MHz RX: 145.325 MHz RX: 144.725 MHz

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info