Bedienungsanleitung Kenwood TH-F7E (Seite 28 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 SCAN

◆

To perform the Program Scan, the following conditions must

be met. Otherwise, the Band scan starts {page 22}.

•

The upper and lower limit frequencies are in the same

frequency band.

•

Ln < Un (where “n” is the Program Scan channel number).

MHz SCAN

MHz Scan allows you to scan an entire 1 MHz

frequency range within the current VFO frequency.

1 Press [VFO].

2 Turn the Tuning control or press [ ]/ [ ] to select

a frequency in which to perform the MHz Scan. If

you want to scan the entire 145 MHz frequency,

select any frequency between 145.000 and

149.995 MHz (for example, select 145.650 MHz).

Scan will operate between 145.000 MHz and

145.999 MHz.

3 Press [MHz] (1 s) to start the MHz Scan.

4 To stop the MHz Scan, press [MHz] or [PTT].

Note:

◆

If the Fine Tuning function is ON, you cannot perform the MHz

Scan.

◆

If you press [MONI], MHz Scan temporarily pauses. Release

[MONI] to resume scanning.

PROGRAM SCAN

You can limit the scanning frequency range. There

are 10 memory channel pairs (L0/U0 ~ L9/U9)

available for specifying the start and end frequencies.

It monitors the range between the start and end

frequencies that you have stored in memory channels

L0/U0 to L9/U9. Before performing the Program

Scan, store the Program Scan frequency range to

one of the memory channel pairs L0/U0 ~ L9/U9.

■ Storing Program Scan Frequency Range

1 Press [VFO].

2 Press [BAND] to select your desired band.

3 Turn the Tuning control or press [ ]/ [ ] to

select your desired start frequency.

4 Press [F], then turn the Tuning control or press

[ ]/ [ ] to select a memory channel from L0 ~

L9.

5 Press [MR] ([ ] or [MNU]) to store the start

frequency in the memory channel.

6 Turn the Tuning control or press [ ]/ [ ] to

select your desired end frequency.

7 Press [F], then Turn the Tuning control or

press [ ]/ [ ] to select the corresponding

channel from U0 ~ U9 (you must select the

same numeric value as in step 4).

• For example, if you selected L0 in step 4,

you must select U0 in this step.

8 Press [MR] ([ ] or [MNU]) to store the end

frequency in the memory channel.

■ Performing the Program Scan

1 Press [VFO].

2 Turn the Tuning control or press [ ]/ [ ] to

select a frequency within the frequency range

of memory channel L0/U0 ~ L9/U9.

3 Press [VFO] (1 s) to start the Program Scan.

4 To stop the Program Scan, press [VFO] or

[PTT].

Note:

◆

If you press [MONI], Program Scan temporarily pauses.

Release [MONI] to resume scanning.

◆

If the Fine Tuning function is ON, the scanning does not stop

at the busy channels.

◆

The transceiver stops scanning in all modes when it detects

a signal.

◆

If more than 2 Program Scan channel pairs are stored and

overlaps the frequency range among the pairs, the smaller

Program Scan memory channel number has the priority.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info