Bedienungsanleitung Kenwood TH-F7E (Seite 30 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 SCAN

CALL SCAN

A Call channel can be stored for each amateur radio

band, such as the 2 m, 70 cm, and 1.25 m (TH-F6A

only) bands {page 19}. You can monitor one of these

Call channels and the current operating frequency

alternatively.

1 Select the frequency (in VFO, Memory Recall, or

Information Channel mode) you want to monitor.

• In VFO mode, press [A/B] to select the A or

B-band. Then, turn the Tuning control or press

[ ]/ [ ] to select the desired frequency.

• In Memory Recall mode, turn the Tuning

control or press [ ]/ [ ] to select a memory

channel you want to monitor.

• Press [INFO] to recall the last Information

Channel you monitored.

2 Press [CALL] (1 s) to start the Call Scan.

3 The Call channel for the band and the selected

VFO frequency, memory channel or Information

Channel are monitored alternately.

4 To stop the Call Scan, press [PTT] or [CALL].

Note:

◆

The transceiver stops scanning in all modes when it detects a

signal.

◆

You can perform the Call Scan even if the recalled memory

channel or Information channel has been locked out {page 27}.

◆

If the Call channel is not available for the current operating

frequency, an error beep sounds.

PRIORITY SCAN

You may sometimes want to check your favorite

frequency activities while monitoring the A and

B-bands. In this case, use the Priority Scan function.

It checks the activities of Pr1 and Pr2 channels every

3 seconds, alternately, using the B-band receiver.

If the transceiver detects a signal on Pr1 or Pr2, it

recalls the frequency to the B-band receiver.

Note: If you do not operate any control or key for 3 seconds after the

signal drops, the transceiver returns to the original frequency and

resumes Priority Scan.

PROGRAMMING PRIORITY CHANNELS

1 Press [VFO].

2 Turn the Tuning control or press [ ]/ [ ] to select

your desired priority channel frequency.

3 Select the mode and selective call functions, if

necessary.

4 Press [F].

• The memory channel number appears.

5 Turn the Tuning control or press [ ]/ [ ] to select

“Pr1”.

6 Press [MR] ([ ] or [MNU]) to store the data on the

priority channel.

• If you want to store a second priority channel,

repeat steps 1 ~ 6 and select “Pr2” in step 5.

Note: You can program any frequency available on the B-band as a

priority channel.

USING PRIORITY SCAN

1 Press [F], [BAL].

•“” appears.

• The transceiver checks for a signal on the Pr1

and Pr2 channels every 3 seconds, alternately.

• When the transceiver detects a signal on the

priority channel, “Pr1” or “Pr2” blinks and the

B-band frequency changes to the priority

channel.

• If you do not operate any control or key for

3 seconds after the signal drops, the

transceiver returns to the original frequency

and resumes Priority Scan.

2 To quit Priority Scan, press [F], [BAL] again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info