Bedienungsanleitung Kenwood TH-F7E (Seite 32 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 SCAN

USING VISUAL SCAN (MEMORY CHANNEL)

1 Press [MR] to enter Memory Recall mode.

2 Turn the Tuning control or press [ ]/ [ ] to select

your desired center memory channel.

3 Press [F], [INFO] to start the Visual Scan.

• The transceiver start scanning the 5 upper

memory channels and 5 lower memory

channels, by centering the selected memory

channel.

• The current scanning memory channel number

and frequency are displayed on the current

operating band. On the other band, the relative

S-meter level of each frequency channel is

displayed.

• To pause Scan, press and hold [MONI]. While

the Visual Scan is paused, the center

frequency bar-graph blinks and you can

monitor the frequency. Release [MONI] to

resume the Visual Scan.

4 To change the current scanning channel, turn the

Tuning control or press [ ]/ [ ].

5 To stop the Visual Scan, press [F], [INFO].

Note:

◆

You can press [PTT] (or [CALL] if 1750 Hz is programmed) to

transmit during the scan if the center frequency is within the

transmission frequency range. The center bar-graph blinks while

transmitting.

◆

If 11 or more memory channels are stored, “

” and “

” do not

appear.

◆

Even if the Fine Tuning ON status is stored in the memory

channels, the Visual Scan (Memory Channel) starts.

MEMORY CHANNEL LOCKOUT

You can lock out memory channels that you prefer

not to monitor during Memory Scan.

1 Press [MR] to enter Memory Recall mode.

2 Turn the Tuning control or press [ ]/ [ ] to select

the memory channel to be locked out.

3 Press [F], [MHz].

•“” appears at the top right of the memory

channel number, indicating the channel is

locked out.

4 To unlock the memory channel, repeat steps 1 ~ 3.

•“” disappears.

Note:

◆

The Program Scan memories (L0/U0 ~ L9/U9) and Priority

channels (Pr1 and Pr2) cannot be locked out.

◆

Even if a memory channel is locked out, you can perform the Call

Scan {page 25} between the Call channel and memory channel.

◆

If the same memory channel is recalled to the A and B-band, you

cannot lock out the channel.

SCAN RESUME METHOD

The transceiver stops scanning at the frequency (or

memory channel) where a signal is detected. It then

continues or stops scanning according to which

resume mode you have selected.

• Time-Operated mode (default)

The transceiver remains on a busy frequency (or

memory channel) for approximately 5 seconds,

then continues to scan, even if the signal is still

present.

• Carrier-Operated mode

The transceiver remains on the busy frequency (or

memory channel) until the signal drops out. There

is a 2-second delay between signal dropout and

scan resumption.

• Seek mode

The transceiver moves to a frequency or memory

channel where a signal is present and stops.

To change the scan resume method:

1 Press [MNU].

2 Turn the Tuning control or press [ ]/ [ ] to select

Menu No. 1 (SCAN RESUME).

3 Press [ ] or [MNU].

4 Turn the Tuning control or press [ ]/ [ ] to select

“TIME ” (Time-Operated mode), “CARRIER”

(Carrier-Operated mode), or “SEEK” (Seek mode).

5 Press [ ] or [MNU] to store the setting.

Otherwise, press [ ] or [PTT] to cancel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info