Bedienungsanleitung Kenwood TH-F7E (Seite 34 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 SELECTIVE CALL

CTCSS FREQ. ID SCAN

This function scans through all CTCSS frequencies to

identify the incoming CTCSS frequency on the

received signal. You may find this useful when you

cannot recall the CTCSS frequency that the other

persons in your group are using.

1 While the CTCSS function is ON, press [F],

[TONE] (1 s) to start the CTCSS Freq. ID Scan

function.

• To reverse the scan direction, turn the Tuning

control or press [ ]/ [ ].

• To quit the function, press [ ] or [PTT].

• When a CTCSS frequency is identified, the

identified frequency appears and blinks.

2 Press [ ] or [MNU] to program the identified

frequency in place of the current CTCSS

frequency. Otherwise, press [ ] if you do not

want to program the identified frequency.

• Turn the Tuning control or press [ ]/ [ ] while

the identified frequency is blinking to resume

scanning.

Available CTCSS frequencies

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

100.76214.79323.141435.602

203.96310.001422.641537.012

309.17415.301524.151631.812

404.47512.701627.651737.522

500.77619.011722.261831.922

607.97718.411829.761936.332

705.28818.811928.371048.142

804.58910.321039.971143.052

905.88023.721132.681241.452

015.19128.131238.291

118.49225.631335.302

Note:

◆

Received signals are monitored through the speaker while

scanning is in progress.

◆

CTCSS Freq. ID Scan does not scan the tone if a signal is not

detected.

◆

If the CTCSS function is activated for both the A and B-band, the

scan speed may be slower.

DCS

DCS is similar to CTCSS. However, instead of using

an analog audio tone, it uses a continuous sub-

audible digital waveform that represents a 3-digit

octal number. You can select a DCS code from

among the 104 DCS codes listed in the table below.

USING DCS

Press [TONE] until “DCS” appears.

• Each time you press [TONE], the icon cycles as

follows: “ ” (TONE) ➞ “CT” (CTCSS) ➞ “DCS”

(DCS) ➞ “ ” (OFF) ➞ “ ” (TONE).

When the DCS function is ON, you will hear calls only

when the selected DCS code is received. To answer

the call, press and hold the PTT switch, then speak

into the microphone.

Note: You cannot use the DCS function and CTCSS/ Tone functions

simultaneously. Switching the DCS function ON after having

activated the CTCSS/ Tone functions deactivate the CTCSS/ Tone

functions.

SELECTING A DCS CODE

1 While in DCS mode {above}, press [F], [TONE].

• The current DCS code appears.

2 Turn the Tuning control or press [ ]/ [ ] to select

your desired DCS code.

• The available DCS codes are shown in the

following table.

320560231502552133314564216137

520170431212162233324664426237

620270341322362343134305726437

130370541522562643234605136347

230470251622662153544615236457

630411551342172653644325456

340511651442472463254625266

740611261542603563454235466

150221561642113173554645307

350521271152513114264565217

450131471252523214464606327

3 Press [ ] or [MNU] to store the new setting.

Otherwise, press [ ] or [PTT] to cancel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info