Bedienungsanleitung Kenwood TH-F7E (Seite 31 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

7 SCAN

Note:

◆

The signal being received on the B-band may become

intermittent because the Priority Scan uses the B-band receiver

to check the priority channel(s) activities.

◆

When a signal is received on a Priority channel with a CTCSS or

DCS code programmed, the Priority channel is recalled even if a

different selective tone/ code is detected. However, the

transceiver only unmutes if the signal has the same CTCSS tone

or DCS code.

◆

If the Tone Alert function {page 40} is ON for the B-band, it

overrides the Priority Scan function. This means that you cannot

monitor the received signal on the Priority Channels nor transmit

on the Priority Channels.

◆

Press and hold [MONI] to pause the Priority Scan when the

transceiver is not displaying a priority channel. Release [MONI]

to resume the Priority Scan.

◆

If you clear the Priority Channels {page 16}, the Priority Scan

stops.

◆

If you press any key other than the following keys while “Pr1” or

“Pr2” is blinking, the transceiver exits the Priority Scan: [LAMP],

[MONI], [A/B], [SQL], [BAL], [F] (1 s), and [PTT].

◆

If you perform the Visual Scan {below} while Priority Scan is

activated, the Priority Scan temporarily pauses.

INFORMATION CHANNEL SCAN

Information Channel Scan is similar to Group Scan.

However, it scans only Information channels.

1 Press [INFO].

• The last Information channel you used is

recalled.

2 Press [INFO] (1 s) to start the Information

Channel Scan.

3 To stop the Information Channel Scan, press

[INFO].

• If necessary, press [A/B] to select the B-band

and then press [VFO] or [MR] to select another

frequency (channel) for the B-band.

Note:

The transceiver stops scanning in all modes when it detects a

signal.

VISUAL SCAN

While you are receiving, Visual Scan allows you to

monitor frequencies near the current operating

frequency. Visual Scan graphically displays the busy

status of all frequencies in the selected range on the

other band display area. You will see 6 different bar-

graph levels, for each frequency (channel) point that

represent relative S-meter levels.

The Visual Scan monitors ±5 channels (frequencies)

by centering on the current channel (frequency). In

this way, a total of 11 channels’ (frequencies’) signal

strength status are graphically displayed.

Note:

◆

When you perform the Visual Scan on the A-band, the

transceiver can output the audio. However, when you perform

the Visual Scan on the B-band, it cannot output the audio. The

S-meter does not reflect the signal strength, neither.

◆

When the VOX function is activated, you cannot perform the

Visual Scan.

◆

When the Visual Scan is in progress, the other scan functions.

USING VISUAL SCAN (VFO)

1 Select your desired band for Visual Scan.

2 Press [VFO].

3 Turn the Tuning control or press [ ]/ [ ] to select

your desired center frequency.

• The transceiver scans the 5 upper frequencies

and 5 lower frequencies using the current VFO

frequency step {page 37}.

4 Press [F], [INFO] to start Visual Scan (VFO).

• The scanning frequency is displayed on the

current operating band and the relative

S-meter level of each frequency appears on

the other band display.

• To pause Scan, press and hold [MONI]. While

the Visual Scan is paused, the center

frequency bar-graph blinks and you can

monitor the frequency. Release [MONI] to

resume the Visual Scan.

5 To change the current scanning frequency, Turn

the Tuning control or press [ ]/ [ ].

• The displayed frequency changes and the

cursor moves.

6 To stop the Visual Scan, press [F], [INFO].

Note:

◆

You can press [PTT] (or [CALL] if 1750 Hz is programmed) to

transmit during the scan if the center frequency is within the

transmission frequency range. The center bar-graph blinks while

transmitting.

◆

If the Fine Tuning function is ON, the Visual Scan cancels the

Fine Tuning function and automatically adjusts the frequency to

the next available frequency.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info