Bedienungsanleitung Kenwood TM-D710GA (Seite 63 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

APRS-18

STORING AUTO MESSAGE REPLY

Enter Menu mode and access Menu 622.

■ Auto Answer Reply <REPLY>

While you are driving, for example, you cannot immediately

answer to received messages. On this transceiver, you can

program the message to be automatically returned when a

message is received.

You can choose from the following delay times: [ON

(DELAY TIME NONE)], [ON (DELAY TIME 10 sec)], [ON

(DELAY TIME 30 sec)]. As an example, when selecting [ON

(DELAY TIME 10 sec)], your auto response message will be

transmitted approximately 10 seconds after having received a

message.

• The auto response message will be cancelled if you

operate the transceiver before the delay time expires,

after having received a message.

• “AA:” (Auto Answer) is automatically added to the top of

the auto response message.

1 Rotate the Tuning control to select “ON (DELAY TIME

NONE)”, “ON (DELAY TIME 10 sec)”, or “ON (DELAY

TIME 30 sec)”, then press the Tuning control.

2 Rotate the Tuning control to select “TEXT”, then press

the Tuning control.

• The display for entering a message appears; the ﬁ rst digit blinks.

• You can enter alphanumeric characters plus special ASCII

characters.

■ Reply To Callsign <REPLY TO>

When there is a message you would like to reply to for the

speciﬁ c callsign, preset that callsign for automatic responses.

PROGRAMMING A MESSAGE GROUP CODE

Enter Menu mode and access Menu 623.

Use a message group code to exchange messages only among

your group members. With one or more message group codes

programmed, you will receive messages that include the same

group code(s), besides messages addressed to you. If you

program one or more bulletin group codes, you will not receive

bulletins addressed to other speciﬁ c groups. You can program

any desired code using alphanumeric characters; up to 9

characters for messages, and up to 4 characters for bulletins.

You can also program up to 6 codes at the same time; each code

must be separated by a comma (,). If you program 3 message

group codes, for example, you will receive all messages that

include one of the 3 codes. If you program 3 bulletin group codes,

you will reject bulletins addressed to speciﬁ c groups which do not

use any of the 3 codes.

• You can enter 0 to 9, A to Z, , (comma), and –. For messages, “ ” is

also selectable.

• The keypad on the microphone also is available to enter

alphanumeric characters.

• In order to include a message group code in your outgoing packet,

enter a group code in place of a callsign. To include a bulletin group

code, enter it following BLN#; for example, “BLN#ABC” where ABC is

a group code. Use up to 9 characters for a message group code or

up to 4 characters for a bulletin group code.

Note: Unlike a message, a bulletin including a group code will be received by

stations who do not program any bulletin group code.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info