Bedienungsanleitung Kenwood TS-2000E (Seite 76 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

14 SCAN

6 Repeat step 5 to specify the center slow down

frequency points. You can specify a maximum of

5 frequency points for each channel.

7 If you want to clear the slow down frequency

points that you previously stored, press and hold

QUICK MEMO [M.IN] for 1 second.

A confirmation beep sounds and the transceiver

clears all the slow down frequency points you

specified in the memory channel.

Note: You must clear all the previous slow down frequency

points; you cannot clear only specific points.

8 Press [VFO/M] to return to VFO mode.

9 Press [SCAN/ SG.SEL] to start the Program Scan

with the slow down frequency point(s).

Note:

◆

During the Program Scan, you can turn the RIT/ SUB control to

adjust the scanning speed. Turn the control clockwise/ counter-

clockwise to slow down/ speed up the scan. The Program Scan

speed indicator appears on the main dot-matrix display during

the Program Scan; P1 is the fastest speed and P9 is the slowest.

◆

You cannot change the Program Scan speed in FM mode.

◆

You cannot change the scan speed on the sub-receiver.

◆

You cannot specify the Program Scan slow down frequency point

for FM mode.

SCAN HOLD

This function stops Program Scan for approximately

5 seconds, then resumes Scan when you jump to the

desired frequency by turning the Tuning control or the

MULTI/ CH control, or by pressing Mic [UP]/ [DWN].

To use this function, access Menu No. 09, and select

ON. The default is OFF.

MHz SCAN

When you operate the main transceiver or sub-

receiver in VFO mode, you can scan an entire 1 MHz

frequency range within the current VFO frequency.

1 Press [VFO/M] to select VFO mode.

2 Select the desired frequency to perform the MHz

Scan. If you want to scan the entire 145 MHz

frequency, for example, select 145.650 MHz.

Scan will operate between 145.00000 MHz and

145.99999 MHz.

3 Press and hold [1MHz/ SEL] to start the MHz Scan.

4 Turn the RIT/ SUB control to adjust the scan

speed.

5 To stop the MHz Scan, press [SCAN/ SG.SEL] or

[CLR].

Note:

◆

You cannot change the MHz Scan speed in FM mode.

◆

You cannot change the scan speed on the sub-receiver.

MEMORY SCAN

Memory Scan monitors all memory channels in which

you have stored frequencies (All-channel Scan) or only

a desired group of memory channels (Group Scan).

Scan automatically stops at a channel where a signal

is present, regardless of the operating mode. The

transceiver will either remain on that channel for a

short time (Time-operated mode) or until the signal

drops out (Carrier-operated mode). Use Menu No. 10

to select either mode. The default is Time-operated.

SCAN RESUME METHOD

The transceiver stops scanning at the frequency (or

memory channel) where a signal is detected. It then

continues scanning according to which resume mode

you have selected. You can choose one of the

following modes. The default is Time-operated mode.

• Time-Operated mode

The transceiver remains on a busy frequency (or

memory channel) for approximately 6 seconds,

then continues to scan, even if the signal is still

present.

• Carrier-Operated mode

The transceiver remains on the busy frequency (or

memory channel) until the signal drops out. There

is a 2 second delay between signal dropout and

scan resumption.

1 Press [MENU] to enter Menu mode.

2 Turn the MULTI/ CH control to select Menu No. 10.

3 Press [+]/ [–] to select TO (Time-Operated) or CO

(Carrier-Operated).

4 Press [MENU] to complete the setting and exit

Menu mode.

You can lock out the memory channels that you

prefer not to monitor while scanning. To do this, refer

to “Memory Channel Lockout” {page 62}.

ALL-CHANNEL SCAN

Use the following procedure to scan all the memory

channels that contain frequency data in sequence,

ignoring the Memory Group number.

1 Select Time-operated or Carrier-operated mode

via Menu No. 10.

2 Press [VFO/M] to enter Memory Recall mode.

3 Turn the MAIN SQL or SUB SQL control to adjust

the squelch threshold.

4 Press [FUNC], [SCAN/ SG.SEL] to enter Scan

Group Select mode.

• The selected Groups appear in a larger font.

5 Press [•/ DCS/SEL] to deselect all Groups so that

the transceiver scans the memory channel

sequentially, ignoring the Memory Group number

data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info