Bedienungsanleitung Kenwood TS-2000E (Seite 78 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

14 SCAN

3 Press [SCAN/ SG.SEL].

4 The Call channel and the selected VFO frequency

or memory channel are monitored alternatively.

5 To stop Scan, press [SCAN/ SG.SEL] or [CLR].

VISUAL SCAN

While you are receiving, Visual Scan allows you to

monitor frequencies near the current operating

frequency. Visual Scan graphically displays how all

frequencies in the selected range are busy. You will

see a maximum of 7 segments, for each frequency

(channel) point that represent relative S-meter levels.

Determine the scan range by selecting the center

frequency and the number of channels. The default

number of channels is 61.

■ Using Visual Scan (VFO)

1 Select the desired band for Visual Scan.

2 Turn the Tuning control, or press Mic [UP]/

[DWN], to select the operating frequency.

• This frequency will be used as the center

frequency.

3 Press and hold [DISP] for approximately

1 second to start Visual Scan (VFO).

• The center frequency is displayed on the

main frequency display and the current

scanning frequency is displayed on the sub

frequency display. The operating mode and

the number of channels to be scanned are

displayed on the main dot-matrix display.

The sub dot-matrix display shows the

relative S-meter level of each frequency

point, vertically.

• To pause Scan, press [DISP]. “P” appears

on the main dot-matrix display. While the

Visual Scan is paused, you can monitor the

paused frequency. Press [DISP] again to

resume the Visual Scan.

4 To change the current scanning frequency, turn

the Tuning control or press Mic [UP]/ [DWN].

• The displayed frequency changes and the

cursor moves.

• Press [1MHz/ SEL] to make the current

scanning frequency the new center

frequency.

• You can move the frequency using the Tuning

control. If you want to revert to the original

center frequency, press [FM/ AM/ NAR].

5 To quit Visual Scan, press [CLR] or

[SCAN/ SG.SEL].

■ Changing the Number of Channels to Scan

1 Press [MENU] to enter Menu mode.

2 Turn the MULTI/ CH control to select Menu

No. 11.

3 Press [+]/ [–] to select 31, 61 (default), 91 or

181 channels for the number of channels to

scan.

4 Press [MENU] to exit Menu mode.

Note:

◆

The current frequency step of the MULTI/ CH control is used

for the Visual Scan.

◆

While performing the Visual Scan, the DUAL WATCH

function {page 47} is temporarily disabled unless you are

using the 144 MHz or 430/ 440 MHz in FM or AM mode and

the Control Band for the main transceiver.

◆

If you start the Visual Scan from the frequency on the sub-

receiver, the frequency is transferred to the main display,

then the Visual Scan starts.

◆

If you start the Visual Scan in Memory Recall mode, the

memory channel frequencies will be scanned.

◆

Visual Scan stops when you transmit.

◆

Depending on the transceiver conditions, Visual Scan and

the S-meter level may differ.

■ Using Visual Scan (Memory Channel)

1 Press [MENU] to enter Menu mode.

2 Turn the MULTI/ CH control to select Menu

No. 11.

3 Press [+]/ [–] to select 31, 61 (default), 91 or

181 channels for the number of channels to

scan.

4 Press [VFO/M] to enter Memory Recall mode.

5 Press and hold [DISP] for approximately

1 second to start Visual Scan (Memory

Channel).

• The center memory channel number is

displayed on the main frequency display

and the current scanning frequency is

displayed on the sub frequency display.

The operating mode of the center memory

channel and the number of channels to be

scanned are displayed on the main dot-

matrix display. The sub dot-matrix display

shows the relative S-meter level of each

frequency point, vertically.

• To pause Scan, press [DISP]. “P” appears

on the main dot-matrix display. While the

Visual Scan is paused, you can monitor the

paused frequency. Press [DISP] again to

resume the Visual Scan.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info