Bedienungsanleitung Kenwood TS-2000E (Seite 77 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

14 SCAN

6 Press [SCAN/ SG.SEL] to return to Memory

Recall mode.

7 Press [SCAN/ SG.SEL] to start All-channel Scan.

• Scan starts from the current memory channel

and ascends up through the channel numbers

(scan direction cannot be changed).

• To jump to a desired channel while scanning,

turn the MULTI/ CH control, or press Mic

[UP]/ [DWN].

8 To stop Scan, press [SCAN] or [CLR].

Note:

◆

If you are operating on the sub-receiver and perform the Memory

Scan, the transceiver automatically skips the memory channels

that cannot be received by the sub-receiver. The same

conditions apply to the main transceiver.

◆

If you have turned the MAIN SQL or SUB SQL control clockwise,

far beyond the squelch threshold, Scan may fail to stop at a

channel where a signal is present. If this happens, turn the SQL

control slightly counterclockwise.

◆

Starting Memory Scan switches OFF the RIT and XIT functions.

GROUP SCAN

For the purpose of Group Scan, the 300 memory

channels can be divided into 10 groups so that you

can select one or more groups to be scanned,

depending on the situation.

When you store frequency data in a memory channel

{page 58}, the transceiver automatically adds the

default Group 0 (zero), to the memory channel data.

To recall the existing memory channel data and

revise the Group number:

1 Press [M.IN] to enter Memory Scroll mode.

2 Select the desired memory channel by turning the

MULTI/ CH control.

3 Press [DISP].

• The Memory Name input prompt appears.

Press [DISP] again to skip the input or enter a

Memory Name using [+]/ [–] and [MAIN] or

[SUB] {page 63}.

4 Press the desired Group number ([0] to [9]) using

the numeric keypad. The selected Group number

appears in a larger font.

Note: You can select only one of 10 groups (0 to 9) for each

memory channel.

5 Press [M.IN] to store and overwrite the new

channel data to the memory channel.

6 Repeat steps 2 through 6 for each memory

channel you want to assign to a specific group.

You can select a maximum of 10 groups and

sequentially scan the channels that belong to those

groups. Group Scan starts with the smallest group

number and repeats the sequence, for example,

group 3 ➞ group 5 ➞ group 7 ➞ group 3.

1 Select Time-operated or Carrier-operated mode

via Menu No. 10.

2 Press [VFO/M] to enter Memory Recall mode.

3 Turn the MAIN SQL or SUB SQL control to adjust

the squelch threshold.

4 Press [FUNC], [SCAN/ SG.SEL] to enter Scan

Group Select mode. Then, using the numeric

keypad, enter the group numbers you want to

scan. i.e.- Press [3] for group 3, or press [3], [5],

[7] for groups 3, 5, and 7. The selected Memory

Groups appear in a larger font.

5 Press [SCAN/ SG.SEL] to exit Scan Group Select

mode.

6 Press [SCAN/ SG.SEL] again to start Memory

Group Scan.

• Scan ascends up through the channel numbers

(scan direction cannot be changed).

• To jump to a desired channel while scanning,

turn the MULTI/ CH control or press Mic

[UP]/ [DWN].

7 To stop Scan, press [SCAN/ SG.SEL] or [CLR].

After using Group Scan, press [FUNC],

[SCAN/ SG.SEL], then [•/ DCS/SEL] to deselect all

the Group numbers you selected in step 4. This

returns you to All-channel Scan (factory default).

Note:

◆

If you are operating on the sub-receiver and perform the Group

Scan, the transceiver automatically skips the memory channels

that cannot be received by the sub-receiver. The same

conditions apply to the main transceiver.

◆

If you have turned the MAIN SQL or SUB SQL control clockwise,

far beyond the squelch threshold, Scan may fail to stop at a

channel in which a signal is present. If this happens, turn the

SQL control slightly counterclockwise.

◆

When the current channel is within one of the groups that you

selected, Scan starts with the current channel.

◆

When the current channel is outside all the groups that you

selected, Scan starts with the group number that is larger than

and closest to the group number of the current channel.

◆

Starting Memory Scan switches OFF the RIT and XIT functions.

CALL SCAN

A Call channel can be stored for each operating

band, such as HF, 50 MHz, 144 MHz, 430/ 440 MHz

and 1.2 GHz (TS-2000 Optional) bands. You can

monitor one of these Call channels and the current

operating frequency alternatively.

1 Select the frequency you want to monitor.

• In VFO mode, press [A/B] to select VFO A or B

for the main transceiver or press [SUB] or

[CTRL] to select the sub-receiver VFO. Then,

turn the Tuning control or the MULTI/ CH

control to select the desired frequency.

• In Memory Recall mode, press [VFO/M] to

select the memory channel you want to monitor

by turning the MULTI/ CH control.

2 Press [CALL/ C.IN] to recall the Call channel for

the frequency band.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info