Bedienungsanleitung Kenwood TS-590SG (Seite 43 von 96) (Englisch)

606692

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

COMMUNICATING AIDS 7

RISE TIME OF CW

The rise time of a CW signal is the time for the RF

output to rise to its maximum power after the key is

closed.

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to select Menu No. 41.

2 Press [M.IN]/ [SCAN (SG.SEL)] to select “1”, “2”,

“4”, or “6” (default).

• The default setting of 6 ms is ﬁ ne for slow or

medium keying speeds and normal weighting

(dot/ dash ratio). 1, 2, or 4 ms are good for

faster keying speeds.

3 Press [MENU] to exit Menu mode.

AUTO WEIGHTING

The electronic keyer can automatically change the dot/

dash weighting. Weighting is the ratio of dash length

to dot length. The weighting changes with your keying

speed automatically, thus making your keying easier

for other operators to copy (default).

Access Menu No. 42 to select “AUto” or “2.5” ~ “4.0”

(in steps of 0.1) ﬁ xed weight ratio. The default is

“auto”. When a ﬁ xed weight ratio is selected, the dot/

dash weight ratio is locked, irregardless of the keying

speed.

■

Reverse Keying Weight Ratio

Auto Weighting increases the weighting as

you increase your keying speed. However, the

electronic keyer also can decrease the weighting

as you increase your keying speed.

To switch this function ON, access Menu No. 43,

and select “on”. The default is OFF.

When setting Menu No. 42 to “Auto”, refer to the

following.

Reverse

Keying

Weight

Keying Speed (wpm)

4 ~ 24 25 ~ 44 45 ~ 60

OFF 1:2.8 1:3.0 1:3.2

ON 1:3.2 1:3.0 1:2.8

BUG KEY FUNCTION

The built-in electronic keyer can also be used as a

semi-automatic key. Semi-automatic keys are also

known as “Bugs”. When this function is ON, dots are

generated in the normal manner by the electronic

keyer. Dashes, however, are manually generated by

the operator by holding the keyer paddle closed for the

appropriate length of time.

To switch this function ON, access Menu No. 44 and

select “on”. The default is OFF.

Note: When the Bug Key function is ON, CW Message Memory

(see below) cannot be used.

CW MESSAGE MEMORY

This transceiver has 4 memory channels for storing

CW messages. Each memory channel can store

approximately 50 characters (equivalent of 250 dots).

These memory channels are ideal for storing contest

exchanges that you want to send repeatedly. Stored

messages can be played back to check message

content or for transmitting.

The electronic keyer has a function that allows you

to interrupt playback and manually inject your own

keying. To switch this function ON, access Menu

No. 39 and select “on”. The default is OFF.

The electronic keyer can also repeatedly play back the

message that you stored. To switch this function ON,

access Menu No. 62 and select “on”. The default is

OFF.

For repetitive message playback, you can change

the interval between each series of messages. Use

Menu No. 63 and select the time in the range of 0 to

60 seconds, in steps of 1 second.

Note:

◆ This function cannot be used when the Bug Key function is

ON.

◆ Operating the keyer paddle while Menu No. 39 is OFF,

cancels message playback. Even if message playback does

not stop because of your keying start timing, you can cancel

playback by pressing [CLR].

◆ When the constant recording function of the optional VGS-1

is ON, you cannot use [RX/4 (REC)].

■ Storing CW Messages

1 Press [CW/FSK (REV)] until you select CW

mode.

• “CW” appears.

2 Press and hold [CH1 (REC)], [CH2 (REC)],

[CH3 (REC)], or [RX/4 (REC)] to select a

memory channel to be recorded.

• If Constant Recording is ON (Menu No.

61), you cannot store a message to [RX/4

(REC)] {page 63}. The default is ON.

3 Begin sending using the keyer paddle.

• The message you send is stored in memory.

4 To complete the message storage, press [CLR]

or [CH1 (REC)]/ [CH2 (REC)]/ [CH3 (REC)]/

[RX/4 (REC)] to stop.

• When the number reaches 100(%), the

memory becomes full and recording

automatically stops.

Note: If you do not operate the keyer paddle after starting to

record a message, a pause is stored in the channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-590SG Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-590SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info