Bedienungsanleitung Kenwood TS-590SG (Seite 45 von 96) (Englisch)

606692

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

COMMUNICATING AIDS 7

FREQUENCY CORRECTION FOR CW

If you operate both SSB and CW modes, you would

sometimes use SSB mode (USB or LSB) just to

watch and listen to CW signals. It is ﬁ ne just to

monitor those CW signals but you have experienced

that changing the mode from SSB to CW results in

losing the target CW signal. This is because the

frequency on the display always shows the true carrier

frequency for all modes. If you want the transceiver to

shift the reception frequency to trace the receiving CW

signal when changing the mode from SSB (USB or

LSB) to CW, switch this function ON. The transceiver

shifts the reception frequency when changing the

mode from SSB to CW, so you can still hear the target

signal and instantly transmit the signal in CW without

adjusting the frequency.

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to select Menu No. 48.

2 Press [M.IN] to select “on”.

3 Press [MENU] to exit Menu mode.

AUTO CW TX IN SSB MODE

If you operate both SSB and CW modes, you can

conﬁ gure the transceiver to change the operating

mode from SSB (USB or LSB) to CW and then

transmit in CW mode automatically when you operate

the CW keyers.

The mode automatically changes from USB to CW

and LSB to CWR, regardless of the setting for Menu

No. 42 (Frequency correction for changing SSB to

CW). Therefore, when the CW signal is received in

SSB mode, you can operate the paddle or keyer to

immediately communicate CW with another station.

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to access Menu No. 47.

2 Press [M.IN] to select “on”.

3 Press [MENU] to exit Menu mode.

Note: You must switch the CW Break-in function ON to change

the mode and transmit in CW mode {page 34}.

MIC UP/ DWN KEY PADDLE MODE

This function allows you to send CW messages

without using an optional paddle {page 2}. The Mic

[UP] key can be used as the dot paddle and the Mic

[DWN] key can be used as the dash paddle.

To activate Mic UP/ DWN key Paddle mode:

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to access Menu No. 46.

2 Press [M.IN] to select “PA”.

3 Press [MENU] to exit Menu mode.

• Press and hold Mic [DWN] to send dots or Mic

[UP] to send dashes in CW mode.

4 To exit Mic UP/ DWN key Paddle mode, access

Menu No. 46 and select “PF”.

SWAP DOT AND DASH PADDLE POSITIONS

This function reverses the position of the dot and dash

paddle positions. As a default, the left paddle sends

dots and the right paddle sends dashes. When this

function is ON, the left paddle will send dashes and

the right paddle will send dots.

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to access Menu No. 45.

2 Press [M.IN] to select “on”.

3 Press [MENU] to exit Menu mode.

• The left paddle now sends dashes and the right

paddle now sends dots. To return to the normal

paddle positions, access Menu No. 45 and

select “oFF”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-590SG Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-590SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info