606693
72
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
66
11 OPERATOR CONVENIENCES
Receiving Data
There are two ways that the Slave can receive the
data from the Master:
Quick memory 1
(TS-450S/690S: channel 00), or
VFO
This choice is made on the Slave transceiver. On
the TS-870S, Menu No. 55 (DIRECT) can be set to
OFF to receive data into Quick memory, or to ON to
receive data in a VFO. Check your Instruction
Manual for other transceivers. Set Menu No. 27
(TX INH) to ON for a Slave TS-870S.
When receiving data at the Slave transceiver in the
VFO, the data is transferred to the TX side of the
VFO that is currently selected. If the transferred
frequency is simplex, both the RIT and XIT on the
Slave are set to OFF; if a split frequency is
transferred then XIT is set to OFF but RIT is not
changed on the Slave. The IF filter is determined by
the transferred mode. AIP status is determined by
the transferred receive frequency according to the
AIP band memory.
If the Slave transceiver has a Quick or Conventional
memory channel recalled for transmit when the
transfer is done, the data will be rejected. To receive
data into a VFO, select TX and RX using VFOs.
Pin Name
1
2
3
4
5
6
GND
TX/RX
TX/RX
CTS
RTS
NC
Pin
No.
r
e
w
t
y
q
Rear Panel view on
TS-450S/690S/850S/950SDX
ACC 1
Connections
Connect each end of the interconnecting cable to
the COM connector or the ACC 1 connector on the
transceivers.
DSP-100 Users:
You may continue using your DSP-100
DSP Unit with the Transfer function. Connect the
interconnecting cable to either the CONT IN or CONT OUT
connector on the DSP-100, then connect the unused CONT
connector on the DSP-100 to the ACC 1 connector on the
transceiver. The transceiver connected to the CONT IN
becomes the Master; the transceiver connected to the
CONT OUT connector is the Slave.
USING QUICK TRANSFER
Note:
While transmitting data, other functions may work more
slowly.
Transferring Data
The Master is the transceiver that sends data to the
Slave transceiver. If the Master has the RIT function
switched ON, the RIT offset frequency is added to
the receive frequency to be transferred.
1 Switch ON the Transfer function on each
transceiver.
On the TS-870S, activate Menu No. 54
(TRNSFER) function. For the compatible
transceiver, check your Instruction Manual for
the correct method.
2 On the Master transceiver, press
QUICK MEMO [M.IN].
If the Master is a TS-450S/690S, press
[M.IN], select memory channel 00, then press
[M.IN] again.
The displayed receive data is stored in Quick
memory channel 1 on the Master transceiver
(TS-450S/690S: channel 00) and transferred
to the Slave transceiver.
w
e
t
u
i
w
e
t
u
i
TS-870S TS-870S
TS-870S
Cross-wired cable
Cross-wired cable
See IF-232C manual.
IF-232C
Straight cable
COM Connector
cable
TS-450S/690S/850S/950SDX
A
N
T
DIN(6P)
RS-232C(25P)
DIN(6P)
COM (9P)
COM (9P)
COM (9P)
E
X
T
R
X
A
N
T
E
X
T
R
X
A
N
T
72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood TS-870S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kenwood TS-870S

Kenwood TS-870S Bedienungsanleitung - Holländisch - 102 seiten

Kenwood TS-870S Bedienungsanleitung - Französisch - 102 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info