Bedienungsanleitung Kenwood TS-890S (Seite 119 von 196) (Englisch)

683161

119

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Scan is a function that searches for signals by automatically

altering the frequency. This transceiver makes use of the following

scan methods to search for signals.

Scan Type Purpose

Normal Scan

Program Scan

Performs scan in the frequency

ranges that are registered in the

memory channels for specific band

segments (P0 to P9).

VFO Scan

Performs scan on the entire RX

frequency band. When Program

Scan is set to OFF for all the

memory channels for specific band

segments, Program Scan switches

automatically to VFO Scan.

However, when VFO Scan is

selected, VFO Scan is performed

even when not all channels are set

to OFF.

Scan Using

Memory

Channels

All-Channel

Scan

Scans all Memory channels from 00

to 99, P0 to P9, and E0 to E9.

Group Scan

Scans the grouped memory

channels.

Quick Memory

Scan

Scans the Quick Memory channels.

Program Scan

Program Scan performs scan between the range specified by the

start and end frequencies which are registered in the each of

memory channels for specific band segments (P0 to P9).

•

Configure the frequency range for Program Scan in the memory

channels for specific band segments (P0 to P9). Up to 10

frequency ranges that are transmitted by specific stations can

be preconfigured. Enabling standby in a nearby frequency

makes it easy to perform tuning to a specific station when the

station starts communication in the preconfigured frequency

range.

●

Program Scan performs scan between the start and end

frequencies of a memory channel for specific band

segments and moves to the next channel after scanning

of the specified frequency range has ended.

●

While scanning is in progress, turning the Tuning or

[MULTI/CH] control allows the frequency to be changed

quickly. The same operation can also be used to change

the scanning direction.

●

Scanning is performed in the ascending order from low

to high frequency. Configuring the end frequency to a

value smaller than the start frequency by turning the

Tuning or [MULTI/CH] control reverses the scanning

direction (high to low frequency).

●

Scanning is performed based on the step frequency of

the Tuning control when in the SSB, CW, FSK and PSK

modes, while it is based on the step frequency of the

[MULTI/CH] control when in the FM mode, and fixed at

100 Hz in the AM mode.

●

Scanning stops when signals are received while

performing Program Scan (VFO Scan) in the FM mode

or during Memory Scan (All-channel Scan or Group

Scan) or Quick Memory Scan regardless of the operating

mode. For more information on the conditions to resume

scanning, please refer to “Configuring the Conditions for

Resuming Scan” (10-4).

●

During standby for the CTCSS tone in the FM mode,

scan stops only when there is a matching CTCSS tone.

●

When the [SQL] control is turned to the right to a level

that far exceeds the squelch threshold while in the FM

mode, scanning may not stop even at a channel where

a signal is present. Configure the squelch level to a point

that is near the squelch threshold.

Starting the Program Scan (VFO Scan)

1 Press [M/V] to switch to VFO mode.

2 Press F5 [SCAN] to start program scan (VFO scan).

•

Pressing F5 [SCAN] again or [ESC] ends the Program Scan

(VFO Scan).

Configuring the Program Scan (VFO Scan)

Frequency Range

Scanning can be configured to the frequency range specified in

the memory channels for specific band segments (Program Scan)

or the entire RX frequency band (VFO Scan).

To perform Program Scan, register the memory channels for

specific band segments.

1 Press [M/V] to switch to VFO mode.

2 Press and hold F5 [SCAN] to display the VFO/

Program Scan configuration screen.

3 Press F5 [VFO/PROG] to display the Program Scan

segment screen.

Press F2 [ ]/ F3 [ ] to select a memory

channel for specific band segments.

Press F4 [ ] to select whether to scan the

memory channel for specific band segments.

•

Pressing F4 [ ] each time selects (performs scan) or

deselects (does not perform scan) the checkbox.

•

When performing VFO Scan, deselect the checkboxes for

all the memory channels for specific band segments or press

[VFO/PRG] to switch the display to “VFO SCAN”.

•

Pressing F6 [SEL.ALL] selects the checkboxes for all the

memory channels for specific band segments.

•

Pressing F7 [CLR.ALL] deselects the checkboxes for all the

memory channels for specific band segments.

6 Press [ESC] to end the process.

SCAN 10

10 SCAN

10-1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 119

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info