Bedienungsanleitung Kenwood TS-890S (Seite 167 von 196) (Englisch)

683161

167

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Split Transfer

This function allows frequency information to be transferred by

connecting another transceiver to this transceiver as a sub-

receiver. There are two modes for this function: Split Transfer A

and Split Transfer B.

Split Transfer A

This function transfers information on the TX VFO frequency and

mode during split operation from the transceiver (TX/RX end) to

the transceiver that functions as a sub-receiver. This is a

convenient function for simultaneous dual-frequency reception by

having the sub-receiver receive the split frequencies from the TX/

RX end. The sub-receiver also supports the standby function.

Simultaneous Reception of TX Frequency

Split Operation

Sub-receiverTX/RX End

The usable transceiver models are TS-890S, TS-590SG and

TS-590S. TS-590S can be used only as a sub-receiver.

●

Firmware update is needed when TS-590S/ TS-590G is

used as a sub-receiver.

●

The TS-590G series can also be used as a transceiver

at the TX/RX end for Split Transfer A. Firmware update

is necessary regardless of whether it is used as a sub-

receiver or a transceiver at the TX/RX end.

●

Some functions may not be usable during split transfer

between the TS-890 series and another transceiver due

to differences in the specifications.

Split Transfer B

This mode is used for connecting another transceiver to this

transceiver as a sub-receiver during two-man operation while

contesting. This is a convenient function that allows the sub-

operator at the sub-receiver end to transfer frequency and mode

information to the main operator at the TX/RX end.

Operating data can be transferred by the following transceiver

models.

•

TS-890S

•

TS-990S

•

TS-590S

•

TS-590SG

•

TS-480 series

•

TS-2000 series

•

TS-570 series

•

TS-870S

●

Some functions may not be usable during split transfer

between this transceiver and another transceiver.

Connection

Connect the 2 transceivers to enable transfer of frequency data

and sharing of antenna.

●

Cables for connection need to be prepared separately

by the user.

Connection for Data Transfer:

Connect the COM connector of the 2 transceiver units using a

RS-232C cross cable (female-female).

Compatible TransceiverTS-890S

(Female)

RS-232C Cross Cable

(Female)

Connection for Antenna Sharing:

Connect the ANT OUT connector at the TX/RX end to the ANT or

RX IN connector at the sub-receiver end using a coaxial cable.

Turn on the ANT OUT function at the TX/RX end. Select the

connected ANT connector at the sub-receiver end or make use of

the RX ANT function.

Split Transfer A

Below is an example of using this transceiver at both the TX/RX

end and sub-receiver end in the standard settings. Before using

the TS-590SG/ TS-590S as a sub-receiver, please read through

the instruction manual and update documents.

Configuration

Using TS-890S at the TX/RX End

1 Enable this transceiver to function as a TX/RX end

transceiver.

Select “A (TX/RX)” in Menu [7-04] “Quick Data Transfer”.

2 Configure the baud rate to 115200 bps.

Select “115200 [bps]” in Menu [7-00] “Baud Rate (COM Port)”.

3 Set to the VFO mode.

If the transceiver is in the memory channel or quick memory

channel mode, switch it to the VFO mode.

Using TS-890S as a Sub-receiver

1 Enable this transceiver to function as a sub-

receiver.

Select “A (Sub RX)” in Menu [7-04] “Quick Data Transfer”.

2 Configure the baud rate to 115200 bps.

Select “115200 [bps]” in Menu [7-00] “Baud Rate (COM Port)”.

3 Set to the VFO mode.

If the transceiver is in the memory channel or quick memory

channel mode, switch it to the VFO mode.

4 Set to simplex mode.

●

This transceiver functions only at the transfer rate of

115200 [bps].

●

It does not function in the memory channel and quick

memory channel modes.

●

This function cannot be used in the split mode.

OTHER FUNCTIONS 16

16-9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 167

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info