Bedienungsanleitung Kenwood TS-890S (Seite 169 von 196) (Englisch)

683161

169

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

TX Inhibit

This function prevents erroneous transmission. When TX Inhibit is

ON, this transceiver does not carry out transmission even when

[PTT] on the microphone is pressed.

The RX audio also becomes inaudible while [PTT] is pressed.

Inhibit transmission in the following cases.

•

When you want to operate the master transceiver unit as a

receive-only unit during operation in the Split Transfer B mode.

Transmission is not carried out even when this is attempted

using the master transceiver. Audio is also not output.

•

When you do not wish to transmit signals to the host transceiver

while controlling the transceiver via PC using KNS (KENWOOD

NETWORK COMMAND SYSTEM).

Configure in Menu [6-03] “TX Inhibit”

Setting Value Off (default)/ On

●

When TX Inhibit is ON, RX audio is muted when the SS

terminal signal level of the ACC 2 connector is low. RX

audio is also muted while [PTT] is pressed as the signal

level of the SS terminal becomes low.

●

When TX Inhibit is ON, tuning cannot be performed by

the antenna tuner.

●

When using this transceiver as a receive-only unit at all

times, configure this setting to “On” to prevent erroneous

transmission.

Packet Cluster Tuning

Packet cluster tuning can be performed by connecting TM-

D710(A/E), TM-D710G(A/E), RC-D710, TM-D700(A/E) or TH-

D72(A/E) to this transceiver.

Connection

TH-D72(A/E)

Φ2.5mm-Three-pronged Plug

COM Terminal

GND

TXD

RXD

(Female)

9-pin D-SUB Connector

(Solder Side)

9-pin D-SUB

Female

TM-D700(A/E)

PG-5G

RC-D710 + PG-5J

TS-890S

RC-D710 + TM-V71(A/E)

TM-D710(A/E), TM-D710G(A/E)

9-pin D-SUB Male

9-pin D-SUB Female

Receiving Packet Cluster Data

Follow the steps below to operate TM-D710(A/E)/RC-D710/TM-

D700(A/E)/TH-D72(A/E).

1 Switch to the APRS or Navitra mode to receive the

DX packet cluster data.

2 Display the DX packet cluster and align the cursor

with the frequency to tune to.

3 Press the corresponding key to output the

frequency value selected in step 2.

The operating frequency (VFO) is configured based on the

packet cluster data received if the frequency is configurable by

this transceiver.

•

TM-D710(A/E), TM-D710G(A/E), RC-D710: [TUNE] key

•

TM-D700(A/E): [MHz] key

•

TH-D72(A/E): [MENU] key

●

In the VFO mode, the operating frequency (VFO) that is

currently in use is configured. In the memory channel

mode, the most recent operating frequency (VFO) is

configured.

●

Only the RX data sent from TM-D710(A/E)/TM-

D710G(A/E)/RC-D710/TM-D700(A/E)/TH-D72(A/E) is

supported.

●

DX packet cluster data cannot be sent out automatically

to this transceiver.

●

For TM-D700(A/E), version G 2.0 or later is required to

use this function.

●

Production of the TM-D710(A/E), RC-D710 and TM-

D700(A/E) have been discontinued.

●

For more details on the operation information of the DX

packet cluster, please search for information available

on other sources.

OTHER FUNCTIONS 16

16-11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 169

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info