Bedienungsanleitung Kenwood TS-890S (Seite 168 von 196) (Englisch)

683161

168

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Operation

1 Transfer the TX frequency and mode information

during split operation from the TX/RX end to the

sub-receiver end.

By pressing [SPLIT] at the TX/RX end to switch to the split

mode, the TX frequency and mode information is transferred

to the VFO of the sub-receiver and enables the TX frequency

to be received by the sub-receiver.

Subsequently, when there is a change in the TX frequency at

the TX/RX end, the new TX frequency information will be

transferred automatically, and the RX frequency at the sub-

receiver will be adjusted accordingly. Below are some

examples.

•

When the TX frequency is changed using the XIT function

•

When the RX band and TX band are changed at the same

time using the Band Direct key (“RX/ TX Band” needs to be

selected in advance in Menu [3-13] “Band Direct Keys in

Split Mode”.)

•

When the split TX frequency is changed via operation of the

[RIT/XIT] control (“TX Frequency Offset while RX” needs to

be selected in advance in Menu [3-12] “Split Frequency

Offset by RIT/XIT Control”.)

2 Change the RX frequency and mode that are

transferred from the TX/RX end at the sub-receiver

end.

The frequency and mode that are transferred to the sub-

receiver end can be adjusted independently without affecting

the value at the TX/RX end.

To restore the state where the frequency matches with the TX

frequency at the TX/RX end, press [SPLIT] at the TX/RX end

to reactivate the split function.

3 Transfer the frequency detected at the sub-receiver

end to the TX frequency at the TX/RX end.

Pressing [<Q-M.IN] at the sub-receiver end transfers the

current frequency and mode information to the TX VFO at the

TX/RX end.

●

Upon transmission from the TX/RX end, the sub-receiver

switches to the standby mode.

●

The transceiver at the sub-receiver end is inhibited from

transmission.

●

When XIT at the TX/RX end is ON, the XIT frequency is

added to the frequency to be transferred.

●

When RIT at the sub-receiver end is ON, the RIT

frequency is added to the frequency to be transferred.

●

The transceiver at the TX/RX end is unable to receive

the frequency and mode information from the sub-

receiver if it is not configured to the split mode.

●

The transceiver at the TX/RX end is able to receive the

frequency and mode information from the sub-receiver

even when it is in the frequency lock mode.

Muting the Sub-receiver

The RX audio at the sub-receiver can be muted by the TX/RX end.

1 Assign “Mute (Sub Receiver)” to a PF key at the TX/

RX end.

2 Press PF [Mute (Sub Receiver)].

The RX audio at the sub-receiver end is muted.

•

Pressing the PF [Mute (Sub Receiver)] key again unmutes

the RX audio.

Split Transfer B

This function supports the “split transfer” function on models

before the TS-890S. It allows existing users of the “split transfer”

function to continue using it after changing to TS-890S.

Follow the steps below to operate this transceiver. To combine the

use of a transceiver other than this transceiver, please refer to the

instruction manual of the model to be used.

Using TS-890S at the Sub-receiver End (Master)

1 Turn ON Split Transfer B.

Select “B” in Menu [7-04] “Quick Data Transfer”.

2 Tune to the frequency of the party to communicate

with in the VFO mode.

Operate the Tuning control to tune to the frequency of the party

to communicate with.

3 Transfer the frequency and mode information to the

TX/RX end.

Pressing [<Q-M.IN] saves the frequency and mode information

to channel 0 of the quick memory and transfers it to quick

memory channel 0 or VFO at the TX/RX end.

Using TS-890S at the TX/RX End (Slave)

1 Turn ON Split Transfer B.

Select “B” in Menu [7-04] “Quick Data Transfer”.

2 Configure whether frequency and mode

information transferred from the sub-receiver is to

be received by the quick memory channel or VFO.

Select “VFO” or “Quick Memory” in Menu [7-05] “Overwrite

Location (Quick Data Transfer)”.

3 Receive frequency and mode information from the

sub-receiver.

Upon receiving frequency and mode information that are

transferred from the sub-receiver, channel 0 of the quick

memory or VFO is updated according to the setting in step 2.

●

Configure the 2 transceivers that are connected to each

other to the same COM connector baud rate.

●

To prevent malfunction, reboot both transceivers after

configuring the settings.

●

When using this transceiver as a sub-receiver, configure

Menu [6-03] “TX Inhibit” to “On” to prevent erroneous

transmission.

●

The transceiver at the TX/RX end is able to receive the

frequency and mode information from the sub-receiver

even when it is in the frequency lock mode.

16 OTHER FUNCTIONS

16-10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 168

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info