Bedienungsanleitung Koenic KRVC 2320 RC (Seite 23 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782606

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

English

Fig. 11 Press the on/ standby button on the

device or the start/ pause button on

the remote control to start the cleaning

process. The LED of the on/ standby

button shines permanently.

Press the on/ standby button on the

unit or the start/ pause button on the

remote control again to pause the

cleaning process. Press the on/ standby

button on the unit or the start/ pause

button on the remote control again if

you want to continue cleaning.

However, if you do not press a button

within approx. 60 seconds, the vacuum

robot will switch to the standby mode.

In standby mode, the LED is o. To

activate the vacuum robot press the

on/ standby button on the device or

the start/ pause button on the remote

control.

The vacuum robot will automatically

return to the charging base, after the

cleaning task has been ﬁnished or

when the battery is almost empty. If

the robot is used in a dierent room,

it has to be placed in front of the

charging base and the charging base

button on the remote control or the

button on the device has to be pressed.

Fig. 12 When the battery level is low, the

robotic vacuum automatically returns

to the charging station. When returning

to the charging station, the cleaning

process is interrupted.

Clean the suction opening regularly

with the appliance switched o (on/

o switch in position O) and empty

the dust container and the pre-ﬁlter

after each use. Please note the chapter

Cleaning and care.

Set start time with timer

Fig. 13 To start a cleaning process in your

absence, set a start time for cleaning.

Note: You must be near the robot vacuum

cleaner with the remote control. If the blue

LED is o when the timer settings are

completed (sleep/ standby mode), the start

time settings will not be applied.

Set the on/ o switch to position I and press

the on/ standby button on the unit or the start/

pause button on the remote control. The device

is now activated. Press the timer button to set

the start time.

The hour indicator ﬂashes. Use the arrow keys

to set the hours. Then press the arrow

key to set the minutes display.

The minute display ﬂashes. Use the arrow

keys to set the minutes.

Conﬁrm your entry by pressing the timer

button. An acoustic signal sounds and indicates

that the vacuum cleaner has been successfully

pre-programmed.

The LED of the control lamp ﬂashes. At the set

time, the cleaning process starts.

To deactivate the start time, press the Timer

button for approx. 3 seconds. The timer symbol

in the display o the remote control turns o.

Mode Symbols Explanation

Standard mode -• Standard cleaning, areas and edges are

cleaned alternating

Powerful cleaning + • Powerful cleaning, the vacuum cleaner is

moving spirally

Corners and edges cleaning + • The vacuum cleaner is cleaning along edges

and around obstacles.

Areas + • The vacuum cleaner is cleaning areas and

moving in parallel lines

Set mode

Fig. 14 After starting a cleaning task, press the

mode button on the remote control to

set the mode. Follow below table for an

explanation.

Operation as swab

Note: To enhance the cleaning result and to

achieve an equal distribution of water onto

the ﬂoor, it is necessary to soak the cleaning

cloth under running water and slightly wring

it out, before attaching it to the water tank.

This enhances equal ﬂow of water from the

water tank through the cleaning cloth.

Fig. 15 Remove the dust collector. To do so,

press the release button and pull it out.

Fig. 16 Open the rubber cap and ﬁll the water

tank as desired, but not above the MAX

mark. Close the cap again. Make sure

the mop cover is attached correctly.

Attention! Do not use harsh or

corrosive cleaners or additives. Note,

that the addition of detergents might

impair the traction of the product and

hence negatively inﬂuence the cleaning

result. It is recommended to use pure

water only for cleaning. Always observe

the cleaning recommendations and

requirements of the suppliers of the

ﬂooring. Consult the supplier in case of

doubts or uncertainties.

IM_KRVC2320RC_190807_V10_HR.indb 23 7/8/2019 14:43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KRVC 2320 RC Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info