Bedienungsanleitung Koenic KRVC 2320 RC (Seite 25 von 148) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

782606

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

English

Fig. 20 Remove the mop cover from the water

tank and wash it with a little detergent

and rinse it o. Wring the mop cover

slightly and let it dry.

Fig. 21 Attach the mop cover in the correct

position on the water tank. A

replacement mop cover is included.

Recommendations for a better

cleaning result

Vacuuming

• Before starting the vacuuming process,

remove all objects that stand/ lay on the

ﬂoor, which could interfere with the process

or in which the robot could get tangled up

(e.g. toys, carpets with longer cords etc.).

• Make sure that no objects hang down onto

the ﬂoor, in which the robot could get stuck

(e.g. power supply cables, curtains etc.).

• If possible, place chairs on the table during

the vacuuming process, in order to minimize

the number of obstacles on the ﬂoor.

• Block areas, in which the robot could get

stuck (e.g. closets with lowered boards,

tapered areas in between closets etc.).

• Make sure that all brushes can rotate freely

and aren’t blocked. Clean them if necessary.

• Empty the dust container.

Swabbing

• Observe all recommendations listed above.

• Have the robot vacuum the area before

swabbing, in order to reduce the amount of

dust on the ﬂoor.

• Soak the cleaning cloth under running water

and slightly wring it out, before attaching it

to the water tank, to enhance the cleaning

result and to achieve an equal distribution

of water onto the ﬂoor.

• If necessary, pause the swabbing process

and manually wring out the cleaning cloth,

removing bigger particles, before continuing

the process.

Fig. 25 Close the dust collector again and

insert it into the vacuum cleaner. Make

sure it is assembled properly.

Warning

Never use the device without a ﬁlter

Note:

• The two rotating brushes are subject to a

certain amount of wear, depending on the

type of hard ﬂoors you have (e.g. rough,

rustic tiles). Therefore, you must check

them at regular intervals to ensure, that

they’re undamaged.

• Worn rotating brushes may have sharp

edges that can damage sensitive hard

ﬂoors, such as parquet or linoleum.

The Imtron GmbH does not accept any

responsibility for damage caused by worn

brushes

Fig. 26 If the brush roller is blocked by or full

with hair, lint or similar residues remove

and clean it. Press the buttons on the

cap, remove the cap and then remove

the brush roller. Remove hair and

lint, etc. by hand or with a brush. The

assembly takes place in reverse order.

Cleaning and care

Warning

• When cleaning, never use solvents or

abrasive materials, hard brushes, metallic

or sharp objects. Solvents are harmful to

human health and can attack plastic parts,

while abrasive cleaning mechanisms and

tools may scratch the surface(s).

• Never immerse any electrical part of the

product in water or in other liquids during

cleaning. Never place it under running

water.

• Before cleaning, always switch o the

vacuum robot and disconnect the plug of

the charging base from the power supply.

Emptying dust container and cleaning

ﬁlters and mop cover

Note: The dust container should be emptied

every time after vacuuming.

Fig. 22 After vacuuming, remove the dust

container. Press the release button and

pull it out.

Fig. 23 Hold the dust container over a dust bin,

so that the opening with the yellow

ﬂap faces upwards. This way, the dust

will fall downwards, when opening the

container.

Fig. 24 After approx. 3 operating hours, but

at the latest when the performance

decreases, clean the dust pre-ﬁlter, ﬁne

ﬁlter and HEPA ﬁlter. To do this, remove

all ﬁlter components and clean them

separately. The assembly is done in

reverse order. Make sure, that the ﬁlter

insert is correctly assembled. To ensure

this, press the shorter side wall into the

ﬁtting ﬁrst, before pushing in the ﬁlter

on the other sides by pressing down on

the edges.

IM_KRVC2320RC_190807_V10_HR.indb 25 7/8/2019 14:43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Koenic KRVC 2320 RC Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info