Bedienungsanleitung Kona 2022 (Seite 22 von 45) (Englisch)

780519

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

KONA OWNER’S MANUAL

(5) With a through-bolt or bolt-on system, tighten the

fasteners to the torque specications in the hub manufac-

turer’s instructions.

WARNING: Securely clamping the wheel with a

cam action retention device takes considerable force.

If you can fully close the cam lever without wrapping

your ngers around the fork blade for leverage, the

lever does not leave a clear imprint in the palm of your

hand, and the serrations on the wheel fastener do not

emboss the surfaces of the dropouts, the tension is

insufcient. Open the lever; turn the tension adjusting

nut clockwise a quarter turn; then try again. See also

the rst WARNING in this Section, p. 16.

(6) If you disengaged the brake quick-release mechanism

in 3. a. (1) above, reengage it to restore correct brake

pad-to-rim clearance.

(7)

Spin the wheel to make sure that it is centered in the

frame and clears the brake pads; then squeeze the brake

lever and make sure that the brakes are operating correctly.

c. Removing a disc brake or rim brake Rear Wheel

(1) If you have a multi-speed bike with a derailleur gear

system: shift the rear derailleur to high gear (the small-

est, outermost rear sprocket).

If you have a hub-drive multi-speed e-bike with a derail-

leur gear system, follow (1) above, but also make sure

to follow the hub motor manufacturer's instructions and

recommendations if necessary to disconnect any wiring

prior to wheel removal. If you have a single-speed bike

with rim or disc brake, go to step (4) below.

(2) If your bike has rim brakes, disengage the brake’s

quick-release mechanism to increase the clearance be-

tween the wheel rim and the brake pads (see Section 4.C,

g. 12).

(3) On a derailleur gear system, pull the derailleur body

back with your right hand. Some rear derailleurs have a

"lock" button designed to hold the derailleur in an open

position when removing the rear wheel. Feel free to use

this feature if your derailleur is equipped with it.

(4) With a cam action mechanism, move the quick-release

lever to the OPEN position (g. 8b). With a through bolt

or bolt on mechanism, loosen the fastener(s) with an ap-

propriate wrench, lock lever or integral lever; then push

the wheel forward far enough to be able to remove the

chain from the rear sprocket.

(5) Lift the rear wheel off the ground a few inches and

remove it from the rear dropouts.

d. Installing a disc brake or rim brake Rear Wheel

CAUTION: If your bike is equipped with a rear disc

brake, be careful not to damage the disc, caliper or

brake pads when re-inserting the disc into the caliper.

Never activate a disc brake’s control lever unless the

disc is correctly inserted in the caliper.

(1) With a cam action system, move the cam lever to the

OPEN position (see g. 8 a & b). The lever should be on

the side of the wheel opposite the derailleur and free-

wheel sprockets.

(2) On a derailleur bike, make sure that the rear derail-

leur is still in its outermost, high gear, position; then pull

the derailleur body back with your right hand. Put the

chain on top of the smallest freewheel sprocket. Some

rear derailleurs have a "lock" button designed to hold the

derailleur in an open position when removing or reinsert-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kona 2022 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info