Bedienungsanleitung Korg R3 (Seite 11 von 94) (Englisch)

668721

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

Front and rear panel

[PITCH] wheel

Controls the pitch.

[MOD] wheel

Controls the depth of modulation

(cyclic change).

OCTAVE [UP] [DOWN] buttons

Shift the pitch assigned to the keyboard

in one-octave steps over a range of ±3

octaves.

[BANK SELECT] dial

Selects the program bank (A–P).

When the R3 is shipped from the

factory, sounds are organized in

these banks by category.

[MASTER VOLUME] knob

Adjusts the output volume from the

OUTPUT jacks (L/MONO, R) and

headphone jack

[AUDIO INPUT 2] knob

Adjusts the input level from the rear panel [AU-

DIO INPUT 2] jack. The LED will light when

there is an input signal, and will light red if the

input is overloaded.

AUDIO INPUT1 [MIC] jack

Connect a mic to this input. Vocoder-type

programs use the audio signal from this mic

as the modulator.

The [MIC] switch specifies whether this jack

or the rear panel [AUDIO INPUT 1] jack will

be used.

[TEMPO] knob

Adjusts the tempo (speed) of the arpeggio,

LFO, or effect delay. The LED at the right will

blink in synchronization with the tempo.

PROGRAM SELECT [1] [2] [3]

[4] [5] [6] [7] [8] buttons

Select a program number within

the bank selected by the [BANK

SELECT] dial. (The selected but-

ton will light.) You can also use

these buttons to turn the eight

steps of an arpeggio on/off to vary

the arpeggio performance.

(☞p.15)

In addition, you can hold down the

[SHIFT] button and press one of

these buttons to access the corre-

sponding utility function (☞p.75

SHIFT function).

TIMBRE SELECT [TIMBRE1] (TIMBRE1 SOLO), [TIMBRE2] (TIMBRE 2 SOLO) buttons

Select the timbre(s) that you want to play or edit.

You can solo each timbre by holding down the [SHIFT] button and pressing one of

these buttons.

[MIC] switch

Selects the audio input source for

AUDIO INPUT 1. Select the XLR set-

ting if you're using the front panel

[MIC] jack.

Select the REAR setting if you're us-

ing the rear panel [AUDIO INPUT 1]

jack.

ARPEGGIATOR [LATCH] (CALIBRATION) button

Specifies how the arpeggiator behaves when you release

the keyboard.

You can execute the foot pedal calibration function by hold-

ing down the [SHIFT] button and pressing this button.

ARPEGGIATOR [ON/OFF] (DEMO) button

Switches the arpeggiator on/off (the button is lit

when on).

You can initiate demo playback by holding down the

[SHIFT] button and pressing this button.

[AUDIO INPUT 1] knob

Adjusts the input level from the front

panel [MIC] jack and the rear panel

[AUDIO INPUT 1]. The LED will light

when there is an input signal, and will

light red if the input is overloaded.

[VOCODER] (AUDIO IN THRU) button

Switches the vocoder on/off (☞p.55).

OFF (dark): Vocoder is off.

ON (lit): Vocoder is on.

EDIT (blinking): Vocoder parameters can be edited.

AUDIO IN THRU function

If you hold down the [SHIFT] button

and press this button, the signal

from the [AUDIO INPUT 1] (or MIC)

jack and the [AUDIO INPUT 2] jack

will be passed through to the OUT-

PUT [L/MONO] and [R] jacks

(☞p.79).

Front panel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg R3 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info