Bedienungsanleitung Korg VOX Continental (Seite 22 von 26) (Englisch)

707384

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

En-22

System Settings 9. Wah pedal control

9. Wah pedal control

Use an expression pedal connected to the CONTROL jack to

control the volume or the wah effect. (Default setting: Auto)

1 Hold down the EXIT button and press the EFFECT button.

(The EFFECT button blinks.)

2 Set the desired function using the ORGAN part

VARIATION



,  buttons.

(Auto): When the effect is set to wah (WAH), the pedal

will act as a wah pedal.

When other effects besides wah are selected, the pedal is

used to control the volume.

(Expression): The pedal controls the volume.

3 Push the EFFECT button to apply the settings.

 Push the EXIT button to cancel the settings.

10. Calibrating the pedal

Adjust the polarity and variable range of each pedal connected

to the DAMPER, ROTOR SPEED and CONTROL jacks.

1 Turn off the power on the VOX Continental, and connect all

pedals that you wish to calibrate.

Refer topage 6 for how to connect the pedals.

2 Set the pedal to the minimum value.

Tilt the expression pedal all the way towards you (down).

Lift your foot off damper pedal or the pedal switch.

3 While holding down the EXIT button, press the power

button to turn on the power.

4 When the EXIT button and SCENE 1 button start to blink,

release the buttons. (All other LEDs will go dark.)

Calibrating a pedal connected to the DAMPER jack

5 Press the damper pedal down all the way until it stops,

and then lift your foot off the pedal.

Note: If a pedal is not connected to the DAMPER jack,

press the blinking SCENE 1 button to skip this.

When calibration is finished, the SCENE 1 button will

light.

Calibrating a pedal connected to the ROTOR SPEED

jack

6 Check that the SCENE 2 button is blinking.

Note: If a pedal is not connected to the ROTOR SPEED

jack, press the blinking SCENE 2 button to skip this.

7 Press the pedal switch down all the way until it stops, and

then lift your foot off the pedal.

When calibration is finished, the SCENE 2 button will

light.

Calibrating a pedal connected to the CONTROL jack

8 Check that the SCENE 3 button is blinking.

Note: If a pedal is not connected to the CONTROL jack,

press the blinking SCENE 3 button to skip this.

9 Press the expression pedal upward all the way until it

stops, and then bring the pedal all the way down (towards

you).

When calibration is finished, the SCENE 3 button will

light.

10 When all pedals have been calibrated, you will be able to

play the keyboard again after several seconds.

11. Touch sensor calibration

Calibrate the sensitivity of the touch sensors.

Use these steps to adjust the sensitivity of the touch sensors

depending on your playing environment, if they do not seem

to operate as you like.

1 Turn off the VOX Continental.

2 While holding down the EXIT and CONTROL buttons,

press the power button to turn on the VOX Continental.

The LEDs of the touch sensor on the leftmost side will start

to light up and down.

3 Trace your finger along the touch sensor to chase the LED

lights as they move.

When the touch sensor that is lit is finished calibrating, the

LEDs on the next touch sensor will start to light up and

down.

4 In the same way, trace along the touch sensor to chase the

LED lights as they move.

Do this until you have calibrated all the touch sensors from

left to right.

When all touch sensors have been calibrated, you will be

able to play.

12. Restoring the VOX Continental

to factory-set default settings

The VOX Continental can be returned to its factory default

settings.

This will reset (initialize) the scene data and system

setting data. Any newly created scene data will be

overwritten, and your data will be lost. If you want to

keep your scene data, save the data to a USB storage

device (commercially available). Also, all system settings

(including calibration data) will be reset, and you will

need to make your settings and perform calibration once

more.

While resetting, do not turn off the power, play the

keyboard, or move any buttons, knobs or controllers.

Doing so may cause the reset operation to fail, and you

may be unable to use the instrument.

1 Press the power button while holding down the EXIT and

E. PIANO part select buttons.

The following characters will be shown in the VARIATION

displays of the PIANO and KEY/LAYER parts.

After about five seconds, the VARIATION display and

WRITE button will slowly blink.

2 Press the WRITE button to reset the VOX Continental to

factory default settings.

The following characters will blink in the VARIATION

displays, and after several seconds the keyboard will be

able to be played normally.

 Push any button except for the WRITE button to cancel the

reset operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Korg VOX Continental Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Korg VOX Continental

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info