Bedienungsanleitung Kress 900 hex (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

390125

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

900 HEX/2 English 9

Before any work on the machine itself, pull the

mains plug!

Mounting the curved handle 5 (Fig. A)

The curved handle can be mounted in 3 positions

according to the application and preference of the

user. For mounting in the middle on the top of the

rubber head please proceed as follows:

Position the curved handle with spacer 2 onto the

machine such that the screw of the curved handle

comes lies over the screw opening on the rubber

head.

Turn the locking grip 3 clockwise until the curved

handle sits tightly.

To bring the locking grip back into position over

the curved grip again, it can be lifted, turned to the

required position and latched.

For mounting at the side on the right or left of the

curved handle, proceed in a similar manner but make

sure in doing so that the lugs 1 of the spacer notch in

the recesses 11 provided in the extension of the ven-

tilating slot on the rubber head.

Adjusting the curved handle

The angular position of the curved handle can easily

be adjusted in all 3 positions as the user wishes.

Continue to unscrew the locking grip anticlockwise

until the curved handle can be lifted out of the toothed

grid of the spacer.

Turn the curved handle to the desired position and

allow it to notch in the toothed grid of the spacer.

To tighten the curved handle proceed in the same way

again as for the assembly.

Connect the mains cable module to the handle. The

plug must latch.

Use the mains cable module provided only for

Kress Electro-Tools. Do not attempt to operate

other machines with the module.

Only use original Kress mains cable modules and

at least flexible rubber tube (code designation

H05 RR-F).

Check before putting into operation that the mains

voltage agrees with the voltage specified on the

nameplate of the machine.

Switching on and off

Turn the switching ring 6 in the direction of the arrow.

At the end of the turn the locking switch 7 automati-

cally engages.

By pressing the tilted-up front edge of the locking

switch 7, the switching ring 6 returns to its initial posi-

tion and the machine slowly comes to a standstill.

Full-pulse wave electronics with

tacho-signal recognition

The speed is kept constant due to the integrated full-

pulse wave electronics with tacho-signal recognition.

Gentle-start acceleration is also integrated in the

electronics.

The motor slowly accelerates until the pre-determined

speed is reached, thereby reducing the strain on both

the user and the transmission and prolonging the

service life of the machine.

The electronic overload protection limits the speed

if there is danger of the load causing damage to the

motor. The load on the machine must be reduced in

order for the full capacity to be made available again.

This is best done by briefly taking the machine away

from the work piece.

The thumbwheel 10 enables the optimum speed to be

pre-selected, also while running. The speed required

will depend on the working material and is determined

by trial and error (see application table).

The numbers on the thumbwheel 10 correspond

approximately with the following speeds:

Sanding Plate Brake

The integrated backing pad brake reduces the

number of vibrations at no-load, thus preventing

furrows occurring when positioning the machine on

the work piece.

A steadily increasing no-load speed indicates that

the brake ring is worn und must be replaced.

Curved handle and mains

cable module

7 Putting into Operation

1 4650 RPM

2 5800 RPM

3 7000 RPM

4 8300 RPM

5 9700 RPM

6 11000 RPM

900 HEX/2 - Buch Seite 9 Dienstag, 27. Juni 2000 8:06 08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kress 900 hex Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info