Bedienungsanleitung Krups f 893 (Seite 16 von 39) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

361252

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

We recommend turning the function selector

to position

for about 5 sec. before the

first coffee and after the last coffee of the day

in order to quickly rinse the system and thus

avoid particles of coffee sticking together.

Then wait 30 sec. before starting the

appliance again.

•Remove the capsule holder then place the

capsule upside down in the capsule holder

(10) ; each one contains a single dose of

fresh coffee for a cup of espresso.

•Replace the capsule holder and press until

the handle is facing you or very slightly

offset to the left (11).

•Place the pre-heated cup under the “coffee”

outlet.

•Set the function selector to position

(12).

Once the espresso is finished, reset the

function selector to

, remove the capsule

holder and throw away the used capsule (13).

To ensure that your next espresso is prepared

at the optimum temperature, replace the

empty capsule holder to retain its heat.

Preparing hot water

•Fill the water tank with fresh water.

•Turn the function selector to

•Switch on the appliance and place the hot

water/ steam selector to position

•After the temperature indicator light has

gone out (yellow), immerse the steam nozzle

into a container which you are holding

vertically.

•Turn the function selector to position

(14).

•Once there is enough water in the container,

reset it to

•Next turn the steam nozzle towards the

interior, above the grid so that the drips fall

into the tray.

Take care: the steam nozzle is burning

hot.

Making steam

Steam makes the milk frothy for a cappuc-

cino, and also preheats cups or any kind of

liquid; the noise you hear during this

operation is caused by the intermittent

running of the water pump.

Please note :

Before making steam, make sure that the

capsule holder on the machine is empty

to prevent the coffee becoming dried out

and blocking the hole in the coffee outlet.

Frothing milk for a cappuccino

You can make the milk frothy in order to whip

up a cappuccino. For best results, use the

accessory specially designed for this purpose.

Fit it onto the steam nozzle (15).

Please note:

This accessory must only be used for this

purpose.

• Pour about 100 ml of skimmed milk into a

small high-sided container (maximum

capacity 0.5 L) which will fit beneath the

steam nozzle; the container must also be

chilled (do not rinse it in hot water before

use).

• First prepare an espresso, but only fill the

cup halfway.

• When the yellow temperature indicator light

goes out, dip the the steam nozzle in the

container holding the milk in such a way

that its end is completely immersed in the

milk.

• Turn the function selector to position

(16). During preparation, do not move the

container and make sure that the nozzle

does not touch the bottom, as this would

prevent steam from escaping. Once the

operation is finished, turn the function

selector to position .

• Remove the container and turn the function

selector just for a second to position in

order to eliminate the residue of the milk

which might remain in the end of the

nozzle. Clean the nozzle immediately with a

Art. 893.PM6.5 21/01/04, 11:4416

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups f 893 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info