Bedienungsanleitung Krups f 893 (Seite 17 von 39) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

361252

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

damp cloth each time you have used it to

make frothy milk.

Preheating cups

For the first espressos of the day, we advise

that you pre-heat the cups with very hot

water. Next time you use the machine, you

can pre-heat the cups on the appliance’s own

hotplate.

• Pre-heat the cups with very hot water :

• Turn the function selector to position

• Put the capsule holder in place without a

capsule and start the appliance.

• Place the cup below the capsule holder.

• Once the yellow control light has gone out,

turn the function selector to position

(17) and allow hot water to run into the

cup.

• As soon as the cup is full, turn the function

selector to position

Heating liquids

• Turn the function selector to position

. As

soon as the yellow indicator light goes out,

immerse the steam nozzle into the container

holding the liquid to be heated and turn the

function selector to position (18).

• Once the operation is completed, reset it to

position

Important:

If you want to make an espresso immediately

after making a cappuccino or heating liquid,

the appliance must first be allowed to cool

down to “coffee” temperature. To do this:

• Place the capsule holder in position without

a capsule, put a container below the coffee

outlet and run two cups of water through

via the coffee outlet.

Cleaning

• Never wash your espresso machine

accessories in the dishwasher.

• Empty the water tank after each use.

Each time you make coffee or steam, the

heating system expands (emitting a whistle)

and the water which escapes then runs into

the drip tray; so after about 20 cups of coffee,

the tray must be emptied and cleaned.

Remove the grid and clean this, too.

• Before replacing the tray and the grid, make

sure that the plastic part is correctly

positioned at the back of the drip tray (19).

The best way to clean the capsule holder is to

insert it into the machine, without a capsule,

and turn the function selector to position

In this way it will be cleaned under pressure.

• Reset the control to position

The capsule holder can be cleaned in the

dishwasher and must be cleaned at least once

a week.

• Clean the steam nozzle using a damp

sponge after each use. If the nozzle is

blocked, unscrew the pipe using a coin and

unblock the nozzle with a needle.

• When refitting the pipe, take care that the

rubber seal is correctly positioned (20).

To clean the “cappuccino” accessory, separate

parts A and C from the metal stem B (21);

clean the 3 parts in hot water. If the small

opening at the end A is blocked, you can

unblock it with a fine needle.

For more thorough cleaning, the capsule

cage can be removed:

• Unplug the appliance, remove the water

tank and the drip tray (22).

• Place the machine upside down (23).

• Unscrew the capsule cage with the special

key, anti-clockwise (24-25-26-27).

• Rinse the capsule cage thoroughly under

running water and clean the two perfora-

tions using the unblocking tool (28).

Be careful when using the unblocking

tool, as careless handling could cause

injury.

Art. 893.PM6.5 21/01/04, 11:4417

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups f 893 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info