Bedienungsanleitung Krups XP5220 (Seite 61 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

565305

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

English

n If the pod is not positioned correctly, the result in the cup will not be satisfactory.

n Never use two pods together.

n Then, follow steps of pictures 7 to 11.

WITH A SOFT POD

Your machine is also compatible with soft pods (usually 60 mm in diameter). Given that this

kind of pod is not specifically designed for espresso machines, you will get a less full-bodied

espresso than with an E.S.E. pod.

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4). During the pre-heating phase, the

indicator lamp will flash.

n Place a soft pod in the filter holder. Never use two pods together. If the pod is not positioned correctly,

the result in the cup will not be satisfactory.

n Then, follow steps of pictures 7 to 11.

Steam is used to foam up milk (for example to make a cappuccino or a cafe latte) thanks to the

cappuccino accessory.

To produce steam, the pump works by emitting an intermittent noise.

After using the steam function, the appliance cools automatically by pumping cold water through

the heating system. During the pumping cycles, the excess steam in the heating system is released with

the hot water into the drip tray. The steam and noise that accompany this phase are important for

cooling the appliance.

Warning: during and after using the appliance, the metal parts of the steam nozzle can become very hot.

USING THE STEAM NOZZLE TO FROTH MILK

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4).

n Turn the switch to the “steam preheating” position. The indicator lamp flashes (fig.12).

n Move the steam nozzle towards the outside of the appliance.

n Pour 60 to 100ml of fresh skimmed, semi skimmed or whole milk in a small container of about 1/2 litre

and which can pass under the steam nozzle. The milk and its container should be quite cold.

n We recommend that you use pasteurised or UHT milk and that you avoid using unpasteurised milk.

n As soon as the indicator lamp stops blinking, plunge the steam nozzle into the milk.

n Turn the switch to the “steam” position (fig. 13).

n For a good result, hold the nozzle towards the bottom of the container for about 25 seconds while the

milk heats (without however touching the bottom of the container). Then, bring the container down

gradually so that the nozzle moves up towards the surface (without ever coming out of the milk)

(fig.14).

n Once the froth has formed, turn the switch to the “stop” position (fig.15). The appliance will now

automatically cool itself by launching 3 intermittent pumping cycles. Once this is automatic operation

is complete, you can make a coffee.

Important: To prevent the cappuccino accessory holes from being clogged, the milk foam must not reach

the black plastic ring.

It is important to clean the cappuccino accessory after each use to prevent the milk from drying on the

inside. To do so:

n Place the cappuccino accessory in a container with water.

n Turn the switch to the “steam preheating” position.

7. STEAM FUNCTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Krups XP5220 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info