Bedienungsanleitung Kyocera FS6020 (Seite 84 von 110) (Englisch)

20377

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Chapter 4 Troubleshooting

4-7

Memory overflow

Press GO

The total amount of data received by the printer exceeds the printer’s internal memory.

Check the memory on the status page and delete unnecessary macros and external fonts or

expand printer memory. See

Chapter 6 Option Units

for details about expansion memory. Press

the GO key to resume printing. You can abandon printing by the CANCEL key.

If Auto Continue is set to On, printing will be automatically resumed after a preset period of time.

See

Setting the Auto Continue on page 1-56

MemoryCard err##

Press GO

This message appears when an error occurs during access to the memory card using the

PRESCRIBE RWER command or from the printer’s operator panel.

Look at the error code given in place of ## and see the corresponding description given below.

01: The memory card does not meet specifications. This memory card cannot be used by this

printer. Insert a memory card which can be used by this printer.

02: The memory card is not installed. Recheck the requirements for using the memory card.

04: The capacity of the memory card is insufficient. Clean up files.

05: Specified file not on memory card.

06: No memory for use by memory card. Expand printer memory.

Print overrun

Press GO

The data transferred to the printer was too complex to print on a page.

Press the GO key to resume printing. (The page may break in some pages.)

You can abandon printing by the CANCEL key.

Check the memory on the status page and delete unnecessary macros and external fonts or

expand printer memory. See

Chapter 6 Option Units

for details about expansion memory.

Note:After this message is displayed, page protect mode will be On. To maintain optimum use

of memory during printing, display >Page Protect from the operator panel, and re-

select Auto. See Setting the Page Protect Mode on page 1-51.

If Auto Continue is set to On, printing will be automatically resumed after a preset period of time.

See

Setting the Auto Continue on page 1-56

RAM disk error ##

Press GO

Look at the error code given in place of ## and see the corresponding description given below.

01: Format error. Try turning the power off and on again.

02: RAM disk mode is Off. Turn RAM disk mode On. See

Setting the RAM Disk Size on page 1-

for details.

04: No disk space. Clean up files.

05: Specified file is not on disk.

06: No memory for use by disk system. Expand printer memory.

Virtual mailbox

full

The storage area for the VMB is full.

Print out accumulated VMB data.

Warning

image adapt

Printing job cannot be done in current resolution because there is not enough internal

memory.

Try adding more memory or changing resolution. See

Chapter 6 Option Units

for details about

expansion memory.

Warning

Low memory

The printer’s internal memory is running low due to the number of fonts and macros downloaded.

Print a status page to see how much user memory is left, and try deleting unnecessary fonts and

macros or adding more memory. See

Chapter 6 Option Units

for details about expansion memory.

:Alarm buzzer sounds when an error occurs. Press the CANCEL key to stop the alarm buzzer.

Message Corrective Action

;Ò

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kyocera FS6020 Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info