Bedienungsanleitung La Spaziale RAPID (Seite 7 von 36) (Englisch)

812600

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

MANUAL FOR USE AND MAINTENANCE LSC 001 -UK- REV. 06 7

STARTING UP AND PROGRAMMING THE APPLIANCE

(Range New - Rapid - Spazio - S3 EP/EK - S5 – Compact models)

FOLLOW THE INSTRUCTIONS BELOW (REFERRING TO THE LIST OF PARTS ON PAGES 27/34.

2.1 STARTING UP

FILLING THE BOILER

a) Open the water supply tap as tted during the preparatory stages (2 - Pict.1 - page 6).

Make sure that on the pressure gauge of the motor-driven pump (17) you can read the water mains

pressure ( approx. 4 bar).

c) Push the manual lling valve on the appliance (1) until the boiler level indicator is halfway (2).

In group 1 - Compact models and on models from the Rapid - Spazio range tted with additional steam

wand, to have access to this tap, it is necessary to remove the drip tray (9). The closing of this tap is

manual.

SWITCHING ON THE APPLIANCE

Turn on the main switch (1 - Pict.1 - page 6), as described for the preparation of the system, then turn on

the appliance switch (3) setting it to ON/1 and making sure that the electric connection control light (22),

where present, switches on.

For the S5 range, when the appliance is switched on, the electronic part carries out a check; all symbols on

the control panel are switched on from left to right. At the end of this stage, the symbol for the temperature

setting will start to ash to indicate that the appliance is heating up.

NOTE. According to the amount of water lled manually, it is possible to use the automatic rell

system when the switch (3) is turned on, until the boiler water level indicated by the manufacturer

is reached.

ELECTRIC SWITCHING ON AND BOILER WATER REFILL

In the S5 1 GROUP range, in order to rell the boiler with water , turn on the main switch as arranged

in the preparatory stages ( 1-Pict 1- page 6) ,then open the water supply tap ( 2- Pict 1 page 6 ) making

sure that the water mains pressure is visualized ( approx 4 bar ) on the pressure gauge of the motor-pump

( 17).

Turn the switch knob of the machine to position 1, the LEDS on the touchpad switch on , indicating that

the machine is connected to power , the boiler water rell sets in motion automatically until the boiler water

level indicated by the manufacturer is reached.

ONLY FOR EQUIPMENT FITTED TO OPERATE WITH GAS (optional)

a) Open the gas tap mentioned in the preparation of the system (4 - Pict.1 - page 6).

b) Turn the knob (30) on the machine by 90° until the symbol of the large ame on the knob itself is at the

top.

c) Push the knob (30) and the gas igniter (31) at the same time until the gas turns on; this can be seen

through the inspection opening (41).

d) Hold down the knob (30) for about 10 seconds and check through the special inspection opening (41),

that the ame stays lit.

e) It is recommended to turn the gas adjustment knob (30) to the small ame setting during summer to

prevent useless overheating of the coffee cups on the top grid of the machine (14).



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Spaziale RAPID Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info