Bedienungsanleitung Lexmark Pro715 (Seite 45 von 55) (Englisch)

612374

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

If the cartridges do not seem to fit, then make sure the printhead is properly seated, and then try

installing the cartridges again.

2 Load plain, unmarked paper.

3 From the printer control panel, navigate to:

> Setup > > Maintenance >

4 Press the up or down arrow button to scroll to Deep Clean Printhead, and then press .

A cleaning page prints.

5 Load plain, unmarked paper.

6 From the Maintenance menu screen, press the up or down arrow button to scroll to Align

Printer, and then press

An alignment page prints.

Note: Do not remove the alignment page until printing is finished.

Printer is busy or does not respond

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

following:

AKE

SURE

THE

PRINTER

NOT

LEEP

MODE

If the power light is blinking on and off slowly, then the printer is in Sleep mode. Press to wake up

the printer.

If the printer will not come out of Sleep mode, then reset the power:

1 Unplug the power cord from the wall outlet, and then wait 10 seconds.

2 Insert the power cord into the wall outlet, and then turn on the printer.

If this problem persists, then check our Web site for updates for your printer software or firmware.

ECONNECT

THE

PRINTER

POWER

SUPPLY

1 Turn off the printer.

Note: Make sure the printer is not in Sleep mode. Press and hold

for three seconds to turn off

the printer.

2 Unplug the power cord from the wall outlet, and then pull out the power cord from the power

supply.

3 After one minute, reconnect the power cord into the power supply, and then plug the power cord

into the wall outlet.

4 Turn on the printer.

Cannot delete documents from the print queue

If you have jobs stuck in the print queue and cannot delete them to get other jobs to print, then the

computer and printer may not be communicating.

ESTART

THE

COMPUTER

AND

TRY

AGAIN

EMOVE

AND

RECONNECT

THE

USB

CABLE

CONNECTED

YOUR

PRINTER

Cannot print through USB

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

following:

HECK

THE

USB

CONNECTION

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

2 Firmly plug the square end of the USB cable into the back of the printer.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

The USB port is marked with

Note: If you continue to have problems, then try another USB port on the computer. You may have

connected to a defective port.

AKE

SURE

THE

USB

PORT

ENABLED

INDOWS

1 Click , or click Start and then click Run.

2 In the Start Search or Run box, type devmgmt.msc.

3 Press Enter, or click OK.

The Device Manager opens.

4 Click the plus sign (+) beside Universal Serial Bus controllers.

If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.

For more information, see the computer documentation.

EMOVE

AND

REINSTALL

THE

PRINTER

SOFTWARE

Fax troubleshooting

• “Fax troubleshooting checklist” on page 46

• “Cannot send faxes” on page 46

Troubleshooting 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lexmark Pro715 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lexmark Pro715

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info