Bedienungsanleitung Makita AR410HR (Seite 9 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598404

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

• Ask Makita's Authorized service centers for periodical

inspection of the tool.

• To maintain product SAFETY and RELIABILITY,

maintenance and repairs should be performed by

Makita Authorized Service Centers, always using

Makita replacement parts.

• Use only pneumatic tool oil specified in this manual.

• Never connect tool to compressed air line where the

maximum allowable pressure of tool cannot be

exceeded by 10%. Make sure that the pressure

supplied by the compressed air system does not

exceed the maximum allowable pressure of the

fastener driving tool. Set the air pressure initially to the

lower value of the recommended allowable pressure.

• Do not attempt to keep the trigger contact element

depressed with tape or wire. Death or serious injury

may occur.

• Always check contact element as instructed in this

manual. Screws may be driven accidentally if the safety

mechanism is not working correctly.

SAVE THESE INSTRUCTIONS.

INSTALLATION

Selecting air hose (Fig. 2)

Use a high pressure resistant air hose.

Use an air hose as large and as short as possible to

assure continuous, efficient screw-driving operation.

CAUTION:

• Low air output of the compressor, or a long or smaller

diameter air hose in relation to the screw-driving

frequency may cause a decrease in the driving

capability of the tool.

Lubrication (Fig. 3)

To insure maximum performance, install an air set (oiler,

regulator, air filter) as close as possible to the tool.

Adjust the oiler so that one drop of oil will be provided for

every 30 screws.

When an air set is not used, oil the tool with pneumatic

tool oil by placing 2 (two) or 3 (three) drops into the air

fitting. This should be done before and after use. For

proper lubrication, the tool must be fired a couple of times

after pneumatic tool oil is introduced. (Fig. 4)

FUNCTIONAL DESCRIPTION

CAUTION:

• When adjusting driving depth, always lock the trigger

and disconnect the air hose.

Adjuster (drive depth adjuster) Operating

Method (Fig. 5 & 6)

CAUTION:

• When adjusting driving depth, always lock the trigger

and disconnect the air hose.

This driver is equipped with an adjuster for adjusting

screw driving depth.

Turn the adjuster to adjust driving depth. Driving

adjustment range is 6mm. (one turn of adjuster adjusts

depth by approximately 0.8mm.)

Hook (Fig. 7)

CAUTION:

• When using the hook, or changing its position, always

lock the trigger, and disconnect the air hose.Do not

fasten hook onto waist belt, etc.

• If hook becomes unfastened and the driver drops,

driver may operate by mistake, and lead to injury.

The hook is useful for hanging up the driver temporarily.

The mounting position of the hook on the driver can be

changed.

Remove the hook mounting screw, change position of

hook, and re-secure screw.

Switcher Mode Selection (Fig. 8)

This driver is equipped with a switcher to enable selection

of mode for optimum driving according to the material of

the workpiece. Set to mode positions shown in “Switching

Mode Chart” below for optimum use. Thoroughly turn the

knob until it clicks to a halt properly at either position (1) or

(2). If the driver is used with the switcher in a position

between (1) and (2), driver components may become

damaged, and/or normal performance not achieved.

Suitable for use on general plasterboard with thicknesses

of 9.5mm, 12.5mm and 15mm.

Steel sheet backing up to 0.8mm thick can be worked on

(screws cannot be driven into layered steel sheet

backing).

Always use Makita genuine linked screws.

We recommend that in normal situations the driver be

used in Switching Mode (1), and set to Switching Mode

(2) when screws cannot be driven for lack of power.

ASSEMBLY

Loading Screws

CAUTION:

• Always disconnect air hose from main unit before

loading screws.

• If the main unit is operated by mistake, it may lead to

personal injury.

Steel sheet backing

Steel sheet thickness

0.8 mm

(2) (2) (2)

Steel sheet thickness

0.6 mm

(1) (1) (1).(2)

Steel sheet thickness

0.6 mm

(1) (1) (1)

Wood backing (1) (1) (1) (1)

Screw length 25 mm 28 mm 32 mm 41 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AR410HR Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info