Bedienungsanleitung Makita AR410HR (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598404

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

6. Lower the piston, and then remove the piston cap and

driver bit. (Fig. 26)

Mounting Bit

1. Mount new driver bit onto piston. (Fig. 27)

2. Next, mount piston cap onto piston assembly.At this

point, make sure that piston assembly and piston cap

holes are aligned. (Fig. 28)

- Mount piston cap with hollowed side up as per

diagram.

3. Pass pin through piston assembly. (Fig. 29)

4. Mount rubber ring onto piston assembly. (Fig. 30)

5. Align the bit shape with the shape of driver’s bit

channel and then insert bit. (Fig. 31)

6. Mount top cap onto driver and insert four hex bolts into

holes. (Fig. 32)

7. Firmly tighten hex bolts using hex wrench. At this

point, tighten in order [(1) to (4)] shown by arrows.

(Fig. 33)

- Prescribed tightening torque is between 7.5 and

8.5 N·m

After completing bit replacement, fully check to see that

there are no abnormalities, and then commence driving

screws.

Drain tool

Remove the hose from the tool. Place the tool so that the

air fitting faces down to the floor. Drain as much as

possible.

Cleaning of tool

Iron dust that adhere to the magnet can be blown off by

using an air duster.

Cap

When not in use, disconnect the hose. Then cap the air

fitting with the cap. (Fig. 34)

Storage

When not in use, the tool should be stored in a warm and

dry place.

Maintenance of compressor, air set and air hose. (Fig. 35

& 36)

After operation, always drain the compressor tank and the

air filter. If moisture is allowed to enter the tool, It may

result in poor performance and possible tool failure.

Check regularly to see if there is sufficient pneumatic oil in

the oiler of the air set. Failure to maintain sufficient

lubrication will cause O-rings to wear quickly. (Fig. 37)

Keep the air hose away from heat (over 60°C, over

140°F), away from chemicals (thinner, strong acids or

alkalis). Also, route the hose away from obstacles which it

may become dangerously caught on during operation.

Hoses must also be directed away from sharp edges and

areas which may lead to damage or abrasion to the hose.

(Fig. 38)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Air hoses

• Safety goggles

For European countries only

ENG045-2

Noise and Vibration

The typical A-weighted noise levels are

sound pressure level: 81 dB (A)

sound power level: 94 dB (A).

Wear ear protection.

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

Uncertainty (K): 1.5 m/s

These values have been obtained according to EN792.

EC-DECLARATION OF CONFORMITY

ENH013-7

Model; AR410HR

We declare under our sole responsibility that this product

is in compliance with the following standards of

standardized documents;

EN792 in accordance with Council Directives, 98/37/EC.

CE 2008

Tomoyasu Kato

Director

Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15

8JD, ENGLAND

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita AR410HR Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info